answersLogoWhite

0

On the back trans axle on the side that the belt is on there are 3 plugs the topone is for filling it the middel is the fill line and the botton is the drain, So to chech take a wrench and loosen off the middel plug and check

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

How do you check the hydrostatic fluid on a simplicity lawn mower?

how do i check hydrostatic fluid on mod. 1693305 13hp. lawn tractor


What oil should you use in your simplicity tractor transaxle?

If it is the Toyosha diesel model, use a trans/hydraulic fluid.


Where do you check the hydraulic fluid in a Kubota L285 tractor?

To check the hydraulic fluid in a Kubota L285 tractor, locate the hydraulic fluid reservoir, which is typically found on the left side of the tractor. Remove the reservoir cap and use the dipstick, if available, to check the fluid level. Ensure the tractor is on a level surface and that the engine is off before checking the fluid to get an accurate reading. Add fluid as necessary, following the manufacturer's specifications.


How do you check hydraulic fluid in a branson tractor?

Right next to where to PTO shaft comes out of the back of the tractor there is a sight glass for the hydraulic fluid.


How do you check the hydraulic fluid in a Kubota tractor?

Dipstick


How do you check the hydraulic fluid on a Long Tractor 610?

To check the hydraulic fluid on a Long Tractor 610, first ensure the tractor is on a level surface and the engine is turned off. Locate the hydraulic fluid reservoir, typically found near the rear of the tractor. Remove the dipstick or the cap, clean it, reinsert it, and then remove it again to check the fluid level; it should be within the marked range. If the fluid is low, add the appropriate hydraulic fluid as specified in the owner's manual.


How do you check hydraulic fluid in a tractor?

plug in side of tran or dipsteck


How do you check transmission fluid level in a Massey Ferguson tractor?

finger it


Where do you check the hydraulic fluid level john deere 4310 tractor?

To check the hydraulic fluid level on a John Deere 4310 tractor, locate the hydraulic fluid reservoir, which is typically found near the rear of the tractor. Remove the cap from the reservoir and use the dipstick, if equipped, to check the fluid level. The fluid should be within the recommended range marked on the dipstick or the reservoir. Ensure the tractor is on a level surface and that the engine is turned off during this process for an accurate reading.


How do you check hydraulic fluid on case jx 80 tractor?

To check the hydraulic fluid on a Case JX 80 tractor, first ensure the tractor is on a level surface and the engine is turned off. Locate the hydraulic fluid reservoir, typically found near the rear of the tractor. Remove the dipstick or cap, wipe it clean, reinsert it, and then pull it out again to check the fluid level against the markings. If the level is low, add the appropriate hydraulic fluid as specified in the owner's manual.


How do you check hydraulic fluid on a ford 4200 tractor?

To check the hydraulic fluid on a Ford 4200 tractor, first ensure the tractor is on a level surface and the engine is off. Locate the hydraulic fluid reservoir, usually found on the left side of the tractor near the rear. Remove the dipstick or the fill cap from the reservoir, wipe it clean, reinsert it without screwing it in, and then check the fluid level against the markings on the dipstick. If necessary, add the appropriate hydraulic fluid to reach the correct level.


How do you check hydraulic fluid in 3830 kubota tractor only?

To check the hydraulic fluid in a Kubota 3830 tractor, first ensure the tractor is on a level surface and the engine is off. Locate the hydraulic fluid reservoir, typically marked with a dipstick or sight glass. Remove the dipstick or look at the sight glass to check the fluid level; it should be within the recommended range. If the fluid is low, add the appropriate hydraulic fluid as specified in the owner's manual.