answersLogoWhite

0

If both indicator lights are flashing together, it typically indicates a malfunction in the vehicle's electrical system or a problem with the turn signal relay. This could be caused by a blown fuse, a faulty relay, or a short circuit in the wiring. It's advisable to check the vehicle's manual for troubleshooting steps or consult a mechanic for a thorough diagnosis. Ignoring the issue could lead to further electrical problems or unsafe driving conditions.

User Avatar

AnswerBot

1mo ago

What else can I help you with?

Related Questions

How can I enhance the visibility of my bike during nighttime rides with flashing LED lights?

To enhance the visibility of your bike during nighttime rides with flashing LED lights, consider mounting the lights on both the front and back of your bike. Choose lights with high lumens and multiple flashing modes to increase visibility. Additionally, wear reflective clothing and accessories to further improve your visibility to others on the road.


Why is the right flashing lights flashing faster and both front and rear are working on a cavalier 1997 2.2 and sometimes the flasher on the right side stays lighted on the inside panel?

you lost ground to one of the light sockets or hqve a bad socket in one of the lights


Your 1999 BMW 528i sHow is both the indicator lights EML and ASC what does that mean?

1999bmw eml light on


When crossing railway tracks?

Stop and look both ways..then proceed,unless a rail is down or red lights are flashing.in that case,wait until the rail recedes,or red lights stop flashing.


Is it possible to obtain synchronized flashing state and maintain synchronized flashing without interconnecting two Belisha Beacon lights?

Yes, it is possible to achieve synchronized flashing of two Belisha Beacon lights without directly interconnecting them. This can be done by using a wireless synchronization system that allows the lights to communicate and flash in unison. Additionally, specialized controllers can be employed to ensure both lights flash at the same rate and maintain synchronization over time. This approach provides flexibility in installation while ensuring consistent visual signaling.


Why is the seatbelt airbag light flashing in a 2000 Ford Explorer xls?

Warning lights are important to pay attention to and know warning lights. If seat belt lights flash, and an air bag light flash, it means there are problems with both parts.


How do you stop both lights from flashing when using turn signal?

Have you recently added a trailer hitch? Somewhere the wires have become crossed and that is a common place for it to happen. If anything has been done to any of the lights, that is where I would look first.


How do you install halo projector headlights on a 98 eclipse gs?

splice together both stripped wires for headlights and run your projector lights to your fog lights or park lights


Why do both indicator lights flash and then stay on?

the oven indicator light stays on and the temperature light but i turn the oven nob on and the oven heat up then i turn off . it gos out tell the temperature cools down. then it come back 0n.


What is causing your 1997 Chrysler Town and Country to have both the AC button flashing and the Air circulation button to be flashing non stop?

This is a diagnostic code. You can perform a recalibration by turning the temp to cold and the fan on high. Then hold the rear wiper and rear washer buttons down together. The lights will flash and the test will begin. The test and recalibration concludes with the rear wiper lamp flashes. Press it to end the test. If any other lamps remain flashing note them and got to your dealer for the diagnostic decode.


What are common diabetic eye problems?

You can have Blurry vision, see flashing lights or spots experience pain or pressure in one or both of your eyes. You can also have trouble seeing things out of the corners of your eyes.


When may drivers cross the tracks of an unguarded railroad crossing secured by a flashing light when a train has just passed?

Drivers may only cross the tracks of an unguarded railroad crossing secured by a flashing light after the lights have stopped flashing and it is safe to do so. It's important to ensure that no train is approaching from either direction, as the signals indicate that a train is near. Additionally, drivers should always exercise caution and look both ways before crossing, even after the lights have stopped.