0
John Deere 318 garden tractor What is the valve called that when you pull that lever that lets you push the tractor called It is under the seat deck and mine leaks?
There should be 2 valves right next to each other, they are check valves. Take them out and replace the o-rings and back up ring or the whole assembly if needed. You'll need 2 each of the following part #'s:
R27166 packing o-ring
M45388 back up ring
M45387 o-ring-pur
and the whole assembly AM32939 comes with everything if check valve itself is bad.
Whole assembly $230.00 for the pair
2 o-rings and back up ring $13.00
Price is from a JD Dealer.
What else can I help you with?
How do you repair transmission on poulan garden tractor?
To repair the transmission on a Poulan garden tractor, first, ensure the tractor is turned off and remove the battery for safety. Examine the transmission for any visible damage, leaks, or loose connections. If necessary, replace worn or damaged components such as the drive belt or gear assembly. Reassemble the parts, refill any fluids if needed, and test the tractor to ensure proper operation.
How do you change hydraulic oil in a John Deere 2030 tractor?
To change the hydraulic oil in a John Deere 2030 tractor, start by locating the hydraulic oil reservoir and draining the old oil using the drain plug. Once the oil has fully drained, replace the drain plug and refill the reservoir with the recommended hydraulic oil through the fill port, ensuring to use the correct type and grade as specified in the owner's manual. Finally, check the hydraulic system for any leaks and run the tractor briefly to circulate the new oil, then recheck the fluid level and add more if necessary.
How do you replace the LVA13065 hydraulic filter on a john deere 3320 tractor?
To replace the LVA13065 hydraulic filter on a John Deere 3320 tractor, first ensure the engine is off and allow it to cool. Locate the hydraulic filter, then use an oil filter wrench to remove the old filter, being cautious of any hydraulic fluid that may spill. Before installing the new filter, apply a small amount of hydraulic oil to the rubber gasket, then screw on the new filter by hand until snug. Finally, run the tractor briefly to ensure proper operation and check for leaks.
How do you change the rear main engine seal of a john deere 425?
To change the rear main engine seal on a John Deere 425, first, remove the engine from the tractor by disconnecting all necessary components, including the battery, fuel lines, and wiring harness. Once the engine is out, drain the oil and remove the oil pan to access the rear main seal. Carefully remove the old seal, clean the area, and install the new seal, ensuring it is seated properly. Reassemble the engine, reattach it to the tractor, and refill with oil before testing for leaks.
Where do you put hydraulic fluid in a john deere 2020?
To add hydraulic fluid to a John Deere 2020, locate the hydraulic fluid reservoir, usually found near the rear of the tractor. Remove the cap from the reservoir, and use a funnel to pour in the appropriate hydraulic fluid, ensuring you check the fluid level with the dipstick if equipped. Always refer to the owner’s manual for the correct type of fluid and maintenance guidelines. Make sure to check for leaks and clean any spills after refilling.
How do you replace hydrolic pump on jd 2130?
To replace the hydraulic pump on a John Deere 2130, first, ensure the tractor is turned off and securely parked. Remove the hydraulic fluid from the system, then disconnect the hydraulic lines and any mounting bolts securing the pump. Carefully remove the old pump and install the new one, ensuring proper alignment. Finally, reconnect the hydraulic lines, fill the system with hydraulic fluid, and check for leaks before starting the tractor.
How do you fill transmission fluid on a john Deere la 130?
I believe this has a Peerless 801 transmission, and unless you see leaks where it's parked you may not need to fill it. Overfilling a transaxle can be bad for it. I would check with nearest Jon Deere agency.
How do you change a oil filter on a john deere b?
To change the oil filter on a John Deere B, first, ensure the engine is cool and secure the tractor on a flat surface. Locate the oil filter, typically found near the engine, and use an oil filter wrench to unscrew it. Before installing the new filter, apply a bit of clean oil to the rubber gasket on the new filter, then screw it on by hand until snug. Finally, refill the engine oil if necessary and run the engine briefly to check for leaks.
How does diesel get in oil pan on 231 Massey Ferguson tractor?
the diaphram in the fuel lift pump goes bad and leaks fuel into the engine
Getting Good and Cheap Tractor Tires?
If you need to get tractor tires, it is very important that you get them used. This saves a lot of money because new tractor tires cost--as you probably know--lots. However, you will have to go over the exterior of the tires to make sure there aren't any leaks. Maybe ask to try out the tires before you buy them. Then you can get a sense of any leaks and how serious they are. Ask lots of questions about whatever you are wondering about. Knowledge is power and you will have to understand the product in order to save money.
What is the liquid that leaks out of the cappilleries called?
serum
What is the purpose of a rubber washer in a garden hose?
A rubber washer in a garden hose is used to create a tight seal between the hose and the faucet, preventing leaks and ensuring a steady flow of water.
