you go to alm1 or 2 and keep the reset button pushed in till number flashes then use st stp button to set and to change digits press mode button
To change the SHHORS SH-755 watch from 24-hour format to a 12-hour format, locate the crown on the side of the watch. Pull the crown out to the second click, which allows you to adjust the time. Rotate the crown to set the hour hand past the 12 to switch between AM and PM. Push the crown back in to complete the adjustment.
Hold mode button until alarm time appears push mode button one more time until seconds flash on current time click adjust button to switch between minutes and hours click alarm button to change hour or minute. Click mode to exit "set" mode
It wakes you up at the time you set it to
To set a Spartus alarm clock, first locate the time-setting dial or buttons, typically found on the back or side of the clock. Turn the dial or press the buttons to set the current time, ensuring you adjust for AM or PM if necessary. Next, find the alarm setting feature, which may involve a separate dial or button; set the desired alarm time in the same manner. Finally, ensure the alarm is activated, often indicated by a light or switch.
On the back there should be an alarm set knob (the one with the picture of a bell). On the face of the clock there should be a small, red, short, extra "hand" that doesn't move with the time; that's the alarm setting. Holding the face towards you, turn the alarm knob on the back until the alarm hand points to the time you want the alarm to go off, based on where the hour hand would be (remembering that the hour hand of an analog clock moves slowly between the numbers of this and the next hour, so 6:30 would be halfway between the 6 and the 7). Then there must be a way to turn on/off the alarm. Set this to on before you go to bed at night. In the morning when you wake up you will set this to off to stop the alarm. Don't turn it back on until before you go to bed, or else it will go off at the PM, not the AM, version of the alarm time.
How to set alarm and time
To set the alarm on a WR 50M watch, usually you can press the "Mode" button until you reach the alarm mode. From there, you can press the "Set" button to configure the desired alarm time. Once you have set the alarm time, remember to save the setting and activate the alarm function.
To change the SHHORS SH-755 watch from 24-hour format to a 12-hour format, locate the crown on the side of the watch. Pull the crown out to the second click, which allows you to adjust the time. Rotate the crown to set the hour hand past the 12 to switch between AM and PM. Push the crown back in to complete the adjustment.
Press on mode till you see 'AL' at the top. When you see keep pressing on set button. When minute time starts blinking, adjust the time. When you finished setting time, press set button. Alarm will be set.
To set an alarm on the Accurist MB702S watch, press and hold the "Mode" button until the alarm setting mode activates. Use the "Adjust" button to select the hour, then press "Mode" to move to the minutes and adjust accordingly. Once you have set the desired time, press "Mode" again to confirm and exit the setting mode. Your alarm is now set and will sound at the specified time.
To set the alarm on a digital watch, first, locate the "Mode" or "Alarm" button and press it to enter the alarm setting mode. Next, use the "Set" or "Adjust" button to select the desired hour and minute for the alarm. After adjusting the time, confirm the setting by pressing the "Mode" or "Save" button again. Finally, ensure the alarm is activated, often indicated by a symbol on the display.
To set an alarm on the Fastrack 4050PP02 watch, press the mode button until you reach the alarm setting option. Use the adjust button to select the alarm feature, then navigate to set the desired time using the hour and minute buttons. Once you've set the time, confirm your settings to activate the alarm. Finally, ensure the alarm is turned on, usually indicated by a symbol on the display.
To change your Shhors Lego watch from 24-hour clock mode to 12-hour clock mode, locate the mode or set button on the watch. Press and hold this button until the display starts to blink, then use the adjustment buttons to toggle between the 12-hour and 24-hour formats. Once you’ve selected the desired format, press the mode or set button again to confirm your choice. Check the display to ensure the time is now in the desired format.
To set the alarm on a Pasnew 226 watch, first press the "Mode" button until you reach the alarm setting mode. Then, use the "Set" button to adjust the hours and minutes as needed. After setting the desired time, press the "Mode" button again to save the settings and exit. Make sure the alarm function is activated, usually indicated by an alarm icon on the display.
You can't
To reset the alarm on an Umbro watch, first press the "Mode" button until you reach the alarm setting mode. Then, use the "Adjust" or "Set" button to turn the alarm on or off. If you need to change the alarm time, navigate to the alarm time setting and adjust it using the "Adjust" button. Finally, press the "Mode" button again to exit and save your settings.
First press the mode button three time and enter the second using the date button and press alarm button and enter the minute again press the alarm button and enter the hour and press alarm and set the date and