first throw it out the window then get it do it again if its not at correct tine
Ah, setting a clock can be a peaceful experience, my friend. To set your Sharp Accu-Set Clock Model SPC991, gently locate the "Set" button on the back or bottom of the clock. Press and hold it until the time starts blinking, then use the "+" and "-" buttons to adjust the hours and minutes. Finally, press the "Set" button again to lock in your chosen time. Just like painting a happy little tree, take your time and enjoy the process.
read the diractons
It wakes you up at the time you set it to
On the back there should be an alarm set knob (the one with the picture of a bell). On the face of the clock there should be a small, red, short, extra "hand" that doesn't move with the time; that's the alarm setting. Holding the face towards you, turn the alarm knob on the back until the alarm hand points to the time you want the alarm to go off, based on where the hour hand would be (remembering that the hour hand of an analog clock moves slowly between the numbers of this and the next hour, so 6:30 would be halfway between the 6 and the 7). Then there must be a way to turn on/off the alarm. Set this to on before you go to bed at night. In the morning when you wake up you will set this to off to stop the alarm. Don't turn it back on until before you go to bed, or else it will go off at the PM, not the AM, version of the alarm time.
To set a Spartus alarm clock, first locate the time-setting dial or buttons, typically found on the back or side of the clock. Turn the dial or press the buttons to set the current time, ensuring you adjust for AM or PM if necessary. Next, find the alarm setting feature, which may involve a separate dial or button; set the desired alarm time in the same manner. Finally, ensure the alarm is activated, often indicated by a light or switch.
To turn off the alarm on a Sharp atomic clock, locate the alarm switch on the back or side of the clock and set it to the off position. Depending on the model, you may need to press a specific button or sequence to deactivate the alarm. Refer to the user manual for detailed instructions.
how do you set the alarm on the Timex T434s nature sounds triple alarm clock radio
If your Sharp alarm clock's alarm isn't going off, first check that the alarm is properly set and the time is correct. Ensure that the alarm switch is turned on and that the volume is at an audible level. If it still doesn’t work, try resetting the clock by unplugging it and plugging it back in. If the issue persists, consult the user manual for troubleshooting steps or consider contacting customer support.
To turn off the alarm on an SPC900 Sharp atomic clock, press the "Alarm" button until the alarm time flashes on the display. Then, press the "Set" or "Mode" button to toggle the alarm off. Confirm that the alarm indicator disappears from the display, indicating that the alarm is deactivated. If needed, refer to the specific user manual for detailed instructions.
You can set the alarm volume on a sliding scale of one to ten for the Elgin Travel Alarm Clock.
Ah, setting a clock can be a peaceful experience, my friend. To set your Sharp Accu-Set Clock Model SPC991, gently locate the "Set" button on the back or bottom of the clock. Press and hold it until the time starts blinking, then use the "+" and "-" buttons to adjust the hours and minutes. Finally, press the "Set" button again to lock in your chosen time. Just like painting a happy little tree, take your time and enjoy the process.
uhm i dont think you can set an alarm clock, but you can have a clock on your zune. go to settings and scroll till you see clock, click 'show clock' to yes and set the time to either 12 or 24 hour setting then set your time
To set the alarm on a Sharp SPC 711, first press the "Clock" button to enter the time setting mode. Use the hour and minute buttons to adjust the time you want the alarm to go off. After setting the desired time, press the "Alarm" button to activate it, and ensure the alarm indicator is lit. Finally, you can customize the alarm tone if needed by following the instructions in the user manual.
Set your alarm clock.
read the diractons
Its easy all you have 2 go clock and then you click on time you set your alarm clock and press delete all the the time you set your alarm clock and then you delete it and all of your alarm clock set timer will be deleted and then the time on your phone will go back 2 the way it was
As long as the boombox you have is equipped with this feature, you can set it up. Panasonic, Sharp mini Systems, Sony and GPX are just a few brands that offer this feature in their boomboxes.