0
It will depend on if a lube or dry torque, type of washer used. If lock washer is used then less torque is needed to not damage the lock washer. It should be about 170 ft/lbs max dry with flat washer, if it leaves an imprint in the metal (head or washer) it is too tight. In this case use less torque or down grade. Please note that the washer side is normally the side torqued, regardless of where the washer isi.e. head or threaded side, if concerned then washer both ends.
What else can I help you with?
What is torque bolt spec 18.5 Briggs and stratton?
The torque specification for a bolt in a Briggs and Stratton 18.5 HP engine typically involves tightening it to a specific value, which can vary based on the application and bolt size. For many applications, the torque specifications can range from 20 to 30 foot-pounds. Always refer to the specific service manual for your engine model for precise torque values and procedures to ensure proper assembly and avoid damage.
Is the Torque to fasten the same to unfasten?
The torque needed to loosen a bolt or joint is often much higher than the torque needed to put the bolt in in the first place. There is no set value difference between the two, unfortunately.
What is the maximum torque allowed in M32 10.9 grade bolt?
The maximum torque for an M32 10.9 grade bolt typically ranges from 300 to 400 Nm (Newton-meters), depending on factors such as the type of lubrication and the specific application. It's important to consult the manufacturer's specifications or torque tables for precise values, as these can vary. Additionally, using a torque wrench is recommended to ensure proper tension and prevent bolt failure.
What is the head torque for a John Deere 4239D engine?
head torque sequence, ft lbs, 4239d jd engine
What is mean by reverse torque testing?
Once the initial torque is applied to the fastener, a reverse torque test can be performed to make sure that the fastener has not loosened due to vibration or other conditions like material fatigue or yielding. So, lets say you tighten a bolt to 150inlb with a torque wrench. You should be able to take that torque wrench and apply 150inlb to the bolt in the reverse direction without the bolt loosening (reverse torque is gretaer in almost all cases, depending on materials because initial static friction must be overcome.)
What is the recommended torque specification for chain ring bolt torque?
The recommended torque specification for chain ring bolt torque is typically between 8-10 Nm.
What is the Torque setting for alternator on a Ford Ranger?
The Ford Ranger alternator bolt torque specification is dependent upon the year of the Ford Ranger. In general, the alternator bolt torque specification is 45 pounds.
What is the proper torque specification for tightening a bike wheel bolt?
The proper torque specification for tightening a bike wheel bolt is typically between 30-40 Newton meters. It is important to use a torque wrench to ensure the bolt is tightened to the correct specification to prevent damage to the wheel or hub.
What is the proper torque specification for tightening a bike handlebar bolt?
The proper torque specification for tightening a bike handlebar bolt is typically between 5-7 Newton meters.
What is the recommended torque specification for tightening a bike seatpost bolt?
The recommended torque specification for tightening a bike seatpost bolt is typically between 5-7 Newton meters.
What is the recommended torque specification for fastening a bolt into an m4 thread?
The recommended torque specification for fastening a bolt into an M4 thread is typically around 5.9 to 7.8 Newton-meters.
What is the proper torque specification for tightening the handlebar stem bolt on a bicycle?
The proper torque specification for tightening the handlebar stem bolt on a bicycle is typically between 5-7 Newton meters. It is important to use a torque wrench to ensure the bolt is tightened to the correct specification to prevent damage to the components.
Head and cam torque spec for 1997 1.8 kia sephia?
The 1987 Kia 1.8 liter engine had bolt torque specification is 120 pounds. The camshaft bolt torque specification is 90 pounds.
What is the proper torque specification for tightening a bike stem bolt?
The proper torque specification for tightening a bike stem bolt is typically between 5-7 Newton meters. It is important to use a torque wrench to ensure the bolt is tightened to the correct specification to prevent damage to the bike or injury while riding.
What is the proper torque specification for tightening a bike crank arm bolt?
The proper torque specification for tightening a bike crank arm bolt is typically between 30-40 Newton meters.
What is the recommended torque specification for tightening a bicycle seat bolt securely?
The recommended torque specification for tightening a bicycle seat bolt securely is typically between 10-15 Newton meters.
What is the recommended torque specification for tightening a bicycle seat post bolt?
The recommended torque specification for tightening a bicycle seat post bolt is typically between 10-12 Newton meters.
