0
Sure why not its the same as welding it to a straight piece of pipe
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is difference between weld neck flange and slip on weld flange?
http://www.tubecraftflange.com/products/slipon.htmTubeSlip-On Flanges are probably the most common type of flanges in the industry and are ideal for lower pressure applications. You do not have to specify the pipe schedule when using slip-on flanges due to the fact that its inside diameter is determined by the outside diameter of the pipe. This outside diameter of the pipe does not change for the different schedules. This often makes these easier to stock for vendors. Fabricators also like the fact that these flanges are slightly easier to align than weld neck flanges. They also are slightly easier to cut pipe to the proper length for. They can be used for high temperature and pressure applications but are not generally recommended as compared to other types of flanges. ASME B16.5 Code limits their usage in the 1500#-2500# (lbs.) weight classes.
What is definition of the under run in filet weld?
A fillet weld in any single continuous weldmay underrun the nominal fillet weld size specified by2 mm [1/16 in] without correction, provided that theundersize portion of the weld does not exceed 10% of thelength of the weld. On the web-to-flange welds on girders,underrun shall be prohibited at the ends for a lengthequal to twice the width of the flange.
What is a RFTBE weld neck flange I have never seen RFTBE related to flange description before?
Raised Face Through Bolt End.
What is girth weld?
circumfrencial weld is sometimes referred to as Girth weld. its just another term.
Can you weld steel to steel?
Yes, you can weld steel to steel. You can use steel welding rod.
What is the take out of 6 inches socket weld 90 degree elbow?
what is the take out of 6 inches pipe of a socket weld 90 degree elbow
What is the take out of a 6 inches socket weld 90 degree elbow?
what is the take out of 6 inches pipe of a socket weld 90 degree elbow
Why is filet weld necessary while welding slip on flanges to a pipe end?
It is the only type of weld you can make to seal this type of joint. There are flange ends that can be welded onto pipe with a butt weld, but sockets and slip-ons must be fillet welded.
What is difference between weld neck flange and slip on weld flange?
http://www.tubecraftflange.com/products/slipon.htmTubeSlip-On Flanges are probably the most common type of flanges in the industry and are ideal for lower pressure applications. You do not have to specify the pipe schedule when using slip-on flanges due to the fact that its inside diameter is determined by the outside diameter of the pipe. This outside diameter of the pipe does not change for the different schedules. This often makes these easier to stock for vendors. Fabricators also like the fact that these flanges are slightly easier to align than weld neck flanges. They also are slightly easier to cut pipe to the proper length for. They can be used for high temperature and pressure applications but are not generally recommended as compared to other types of flanges. ASME B16.5 Code limits their usage in the 1500#-2500# (lbs.) weight classes.
What is WNRF flange?
Weld Neck Raised Face flange
What are the types of flanges?
RING TYPE JOINT FLANGE The ring type joint flange metal is used for leak proof process. It is a part of steel. Sometimes the pressure becomes high at that time the ring type joint flange is using. A metal ring is compressed like a seal helps to high-pressure leak proof. THREADED RING FLANGE In threaded ring flange welding is not needed. It is threaded or screwed into another. It is used in low pressure and it can connect only with other threaded material. LAP JOINT RING FLANGE Lap joint includes a stub end or taft. The lap joint is very easy to assemble and align because it is used in low pressure only. A hub is included in a lap joint ring flange but some will not provide to reduce the cost. BLIND RING FLANGE Blind ring flanges are not connectors they are like stoppers. Blind ring flanges are blank because they are used in the end or fitting for periodical inspection only. SOCKET WELD RING FLANGE In socket weld ring flanges the bore of pipe and the flanges both are same, it helps to provide the good flow. The receiver pipe also bored because the socket weld flange and the receiver pipe should tighten. WELD NECK RING FLANGE In weld neck ring flange the boring area and the flanges must be matched to avoid problems inside the pipe. In critical applications the weld neck is durable. SLIP-ON RING FLANGE The slip-on ring flanges don't have neck, it only has a molding area to fit with the pipe. In fabricated applications, the slip-on ring flange is very easy to use. for more check jfindustries
What is Threaded Flange?
A flange threaded in center used for weld or different types of threaded pipe.
What is a WNRF?
Weld Neck Raised Face flange
Who is the best flange manufacturer in India?
Inco Special Alloys is regarded as one of the leading Flange Manufacturers in India. We have various ranges of Flanges in different shapes, sizes, and specifications to fulfil the demands of our clients. We also are Slip-On flange manufacturer, Weld Neck flange manufacturer, Long Weld Neck flange manufacturer, Threaded flange manufacturer, Blind flange manufacturer, socket flange manufacturer etc which are available in various sizes, shapes, and grades. Hence, Inco Special Alloys is one of the best Flange Manufacturer in India. Our Flanges are well-known and respected around the world for their dependability and quality. Therefore, Inco Special Alloys is the top Flange Manufacturer in India. We have a trained staff that guarantees the quality of Flange and other items throughout the production and distribution processes, which makes Inco Special Alloys the top Flange Manufacturer.
What is a sw cl125 150 ff sw flange?
SW = socket weld flanges flange F.F = flat
What is the full form of WNRF flange?
W : Weld N : Neck R : Raised F : Face, It is a type of flange used for butt weld end connection...Refer ASME B 16.5
What is definition of the under run in filet weld?
A fillet weld in any single continuous weldmay underrun the nominal fillet weld size specified by2 mm [1/16 in] without correction, provided that theundersize portion of the weld does not exceed 10% of thelength of the weld. On the web-to-flange welds on girders,underrun shall be prohibited at the ends for a lengthequal to twice the width of the flange.
