0
adding an elbow is like adding another piece of duct,in other words you will gain length. you have to measure using centers. lets say that you have a duct that you want to make an offset to change your location or elevation,measure the distance from starting point to finish point either end to center or center to center,say your measurement is 12in. end to center, measure the elbow from the end to the center,usually by putting it on a table or againist a wall, say your meas. is 6in. bear in mind that the elbow will fit over the duct,lets say 2in. that means the elbow will add 4in. to your duct, subtact 4in.from your 12in.meas. that leaves you with 8in. of duct to make your offset
What else can I help you with?
How do i size an air conditioner?
For a simple residential application 20 to 25 btu/sq ft should be fine. so find the area of the space to be conditioned and multiply by 22.5 and round up or down considering the oreintation of your house. If you have a lot of shade go lower and if you have full sun and a lot of glass go to the high side.
Where can you find science fair project ideas?
Where can i find a science fair project. ----
How can find the tonnage of mechanical press machine?
how can i find the tonnage of mechanical press machine
In which chapter of BS 7671 would you find reference to rotating machines?
Well, darling, if you want to find information on rotating machines in BS 7671, you better flip to Chapter 41. That's where you'll get all the juicy details on those spinning contraptions. So, go ahead and give it a whirl!
What is the design procedure of screw jack?
First step: Find the core diameter of the screw second step: Find the torque required for lifting the screw
How do you find out if you owe the IRS money?
this number will tell you if you have any liens or offsets attached to your ssn 800.304.3107 alt number for irs. 800.829.1040
How do you find out if the IRS owes you money?
this number will tell you if you have any liens or offsets attached to your ssn 800.304.3107 alt number for irs. 800.829.1040
How do you measure an offset for ductwork fittings?
To measure an offset for ductwork fittings, first determine the horizontal and vertical distances between the two duct sections that need to connect. Use a tape measure to find the rise or drop required, then apply the Pythagorean theorem if necessary to calculate the diagonal length of the offset. Mark the measurements on the ductwork, ensuring that angles are accurately measured for proper fitting. Finally, use these measurements to cut and install the appropriate fittings.
Will 4th gen camaro rims fit 3rd gen camaros?
Yes, but you need spacers, not sure what size, find out the respective offsets and do some math.
How do you calculate page numbers and offsets for address references?
To calculate page numbers and offsets for address references, you typically divide the address by the page size to determine the page number, and then find the offset by taking the remainder of the address divided by the page size. This helps locate specific data within a memory system efficiently.
Find LN Round the answer to the nearest tenth?
LM = 4 in LN = ? Find LN. Round the answer to the nearest tenth.
How do you find the offset of a house?
To find the offset of a house, you need to measure the distance from a reference point, such as the property boundary or a street line, to the closest point of the house. Use a measuring tape or surveying tools to ensure accuracy. It's important to check local zoning regulations, as they may specify required offsets from property lines. Additionally, consulting property surveys or blueprints can provide detailed information about offsets.
Where can someone find a round bed?
One can find a round bed at any local IKEA store. One can also find a round bed online from stores like Amazon, My Shopping, Best Buy, Overstock and eBay.
When did C olumbus find out the Earth was round?
he found out the earth was round when he studied geography
To find the mean do you round to nearest tenth?
Only if you were asked to find the mean to the nearest tenth. If so, don't round each number; calculate the mean first and then round it to the nearest tenth.
Who find earth is round?
Christopher Columbus found that the Earth was round in the early 1860's.
How to find the area of round duct?
Area of round duct is pi times radius squared.
