0
60060
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Why square key is stronger against crushing than rectangular key?
it isn't. Assuming both keys are made of the same material, common steel will crush under a force of 95,000 psi (pounds per square inch) and it will shear under a force of 44,000 psi. It is only the depth of material that determines whether it will resist enough force to keep from shearing. if the face of the rectangle and the square material are the same then they will resist the same amount of applied force.
What is the shear strength of a 1 inch diameter steel shaft?
44,000 psi Steel has a shear strength (in single shear) of 44,000 psi; in double shear of 88,000 psi. The area in shear is the diameter of the shaft times the length of the shaft under stress. If it passes through two 1/4" plates with forces acting in opposite directions the shaft will fail with the application of 22,000 pounds of force. If it passes through three sheets of 1/4" plate (with the force on the center plate opposite the other two) the plate will fail with the application of 23,750 pounds of force (compression {crush} failure).
What are equivalent grades of cm 490 steel?
either S355 J2g3 or J0 depends on the sharpy value required
What is a Cold Steel Recon 1 used for?
The Cold Steel Recon 1 is used for stabbing your enemy with great force. Most of the military uses these knifes overseas during combat. That is what it is used for.
Why use high tensile steel?
High tensile steel put simply is used where structures require high tensile strength. Tensile stress is where the forces on a material are "pulling" from each end away from the centre. Steel can be alloyed with certain materials such as aluminum to create a material that is stronger under tensile loading. An example of where high tensile steel is required is the cables of the ANZAC bridge that support its deck. Hope this helps..
What amount of force is needed to bend a steel fence post?
The amount of force that is needed to bend a steel fence post depends with the steel post in question. The force that is required is therefore calculated based on the material in question.
How much force is required to kick down a steel door?
The amount of force needed is dependent on a few variables. The density of the steel door, is the door hallow, and the muscle strength of the person kicking. To accurately assess more information is required.
Force required to upset a .38 in diameter 302 stainless steel solid rivet?
15 tons
What is the most environmentally friendly beverage container?
stainless steel
Can a wolf crush steel in one bite?
A steel can perhaps, but that not steel of any reasonable thickness.
When was Steel Force created?
Steel Force was created in 1997.
On Pokemon ranger shadows of almia where can you find the reggies?
rock: union road before waterfall required: crush lv.5 ice: almia castle in mismagius's room required burn lv. 5 steel: chroma ruins near shadow altar requierd: gallade rock: union road before waterfall required: crush lv.5 ice: almia castle in mismagius's room required burn lv. 5 steel: chroma ruins near shadow altar requierd: gallade
Will a hollow steel ball crush under water?
No. A hollow steel ball will not crush underwater. One reason this is true is because the steel ball cant go under the water in the first place because it hallow.
What are some physical changes with steel?
Some physical changes with steel occur when you melt the steel or when you crush steel.
How much force is required to bend or dent steel?
This is a completely unanswerable question, as it depends on several factors: the composition of the steel in question (there are a great many different alloys that go under the colloquial name "steel"), the type of force being applied (tension, compression, etc.), the design geometries of the object in question, and the environmental factors around the steel (primarily, but not exclusively, the temperature)
How many stories is Steel Force at Dorney Park?
Steel Force is 20 stories tall.
Is a can magnetic?
Some are some aren't. If they are made of steel as some juice cans and a few other beverage cans are they will be. If they are made of aluminum as almost all beverage cans are they will not be.
