0
What else can I help you with?
What is the maximum suction head for pumping water?
I think, that's refer from your system. If you manipulate the surface pressure of the water, you will get a big value of water suction head with higher surface pressure. CMIIW....
What is boiler maximum continuous rating?
The boiler maximum continuous rating (MCR) refers to the maximum amount of steam or hot water that a boiler can produce continuously under standard operating conditions. It is typically expressed in terms of mass flow rate, such as kilograms per hour (kg/h) or pounds per hour (lb/h). The MCR is important for determining the boiler's capacity to meet demand and is a critical factor in system design and efficiency. Understanding the MCR helps ensure that the boiler operates within its safe and efficient limits.
What is the maximum working pressure for r410a at suction line?
The maximum working pressure for R-410A at the suction line typically ranges from about 60 to 70 psi (pounds per square inch) under normal operating conditions. However, it's important to note that the exact pressure can vary based on the specific system design, ambient temperature, and load conditions. Always refer to the manufacturer’s specifications and guidelines for the specific equipment being used.
What are the pros and cons of a capillary tube in refrigeration?
Capillary tube is a very simple device and can be manufacture easily at low cost. The capillary tube can limit the maximum amount of refrigerant to be charged eliminating the need for a receiver in the refrigeration system. Another advantage is when the refrigeration plant is stopped, the pressure along the capillary tube and the entire system remains constant which means that if the compressor is restarted it does not need moreÊpower to overcome high pressure in the system. Hence, smaller compressors can be used instead of big, expensive ones. A disadvantage with capillary coil is that this system is non adjustable due to the fact that the control of the flow of pressure is dictated by the inside diameter of the tube.
How do you build a pressurized system?
How do you build a pressurized system for a container system?
What is the differences between damped and undamped oscillations?
damped vibrations:in damped vibrations the amplitude of the signal decreases with respect to timeundamped vibrationsin undamped vibrations the amplitude of the signal remains constant with respect to time
How damping progressively reduces the amplitude oscillations?
When energy is lost from the oscillating system, the amplitude of oscillationdecreases. When that happens progressively, we say that the oscillation is"damped". "Damping" is a description of the decrease, not its cause.
Define damped oscillation?
Any oscillation in which the amplitude of the oscillating quantity decreases with time is referred as damped oscillation. Also known as damped vibration, http://www.answers.com/topic/damped-harmonic-motion
What is the formula for calculating the amplitude of oscillation in a system?
The formula for calculating the amplitude of oscillation in a system is A (maximum displacement from equilibrium) - (equilibrium position).
How to find the amplitude of oscillation in a given system?
To find the amplitude of oscillation in a given system, measure the maximum displacement from the equilibrium position. This distance represents the amplitude of the oscillation.
What is damped harmonic motion?
Damped harmonic motion refers to the oscillatory motion of a system where the amplitude decreases over time due to a dissipative force, such as friction or air resistance. As the system loses energy to the surroundings, the oscillations become smaller until the system comes to a rest. The damping force causes the system to eventually reach equilibrium.
What is the maximum allowable amplitude for the pendulum motion of this system?
The maximum allowable amplitude for the pendulum motion of this system is the furthest distance the pendulum can swing from its resting position without causing any damage or instability.
Define the terms logging interval dedicated control system and Frequency of Sampling?
what do you mean by terms under damped, critical damped and over damped frequency of control system?
Damping progressively reduces the amplitude of oscillation?
Vibratory motion of ideal systems in the absence of any friction or resistance continues indefinitely under the action of a restoring force. Practically, in all systems, the force of friction slows down the motion, so the systems do not oscillate indefinitely. The friction reduces the mechanical energy of the system as time passes, and the motion is said to be DAMPED. This damping progressively reduces the AMPLITUDE of OSCILLATION.
Is it possible to have damped oscillations when a system is at resonance?
Resonanceis aforcethat remains in a opposite position.It is also observed in physical media such as strings and columns of air. Any waves traveling along the medium will reflect back when they reach the end. It is possible to have damped oscillations when a system is at resonance.
What is the frequency of this damped oscillation?
The frequency of a damped oscillation is the rate at which it repeats its motion. It is determined by the damping factor and the natural frequency of the system.
What is the relationship between the steady state amplitude of forced oscillation and the driving frequency in a mechanical system?
The relationship between the steady state amplitude of forced oscillation and the driving frequency in a mechanical system is that the amplitude of the oscillation increases as the driving frequency approaches the natural frequency of the system. This phenomenon is known as resonance. At resonance, the system absorbs more energy from the driving force, causing the amplitude of the oscillation to be at its maximum.
