Eccentricity is the deflection in the shaft away from truly straight. The turbine shaft when not turning will settle into a bowed shape (measured in thousandths of an inch), this is the deflection from straight. Large turbines are placed on turning gears as they are cooled or warmed up to minimize this deflection. As a turbine is started this eccentricity produces vibration as the deflection changes rotational position, if the turbine is started up too quickly this deflection will increase as a result of inertia trying to deflect the weight of the deflected shaft outward. Eventually the deflection, as a result of rolling the turbine up slowly, will straighten to the true center of the turbine shaft.
centre point of the rotor in relation to shaft
Axial displacement is the motion along the shaft of the turbine caused by the force exerted by the steam or by the thermal expansion of the shaft and casing.
Steam turbine is when a device that has the extract thermal energy from pressurized steam. It is used to do mechanical work on a rotating output shaft. The steam turbine was invented by Sir Charles Parsons in 1884.
The Steam Turbine is the one which steam worked pressured Hot and exited then the shaft of the turbine starts to and fro motion due which energy is injected through nozzle in the receiver.
When Turbine shaft temp is below 100 deg.centigrade,Then rolling of turbine carried out it is called cold rolling.
In large turbines, a valve controls steam flow to groups of nozzles. The number of open valves controls the number of nozzles in use according to the load. A bar-lift or cam arrangement operated by the governor opens and closes these valves in sequence. Such a device is a multi-port valve. Using nozzles at full steam pressure is more efficient than throttling the steam.
agga
Axial displacement is the motion along the shaft of the turbine caused by the force exerted by the steam or by the thermal expansion of the shaft and casing.
eccentricity measurementof shaft at slow roll speed. WITH BEST RGARD AZIZ JAMALI SR SUPERVISOR INSTRUMENT FFBL KARACHI PAK AZIZ.JAMALI@YAHOO.COM +923462243209
It is an engine.A steam turbine is a heat engine that uses the expansion of steam passing through stationary nozzles and blades on a shaft to turn the shaft. The steam can move through the turbine axially (one end of shaft to the other end), radially (shaft to outer casing), or tangentially (around the outer edges of the turbine wheel). In an impulse turbine, the steam is expanded in nozzles and pushes the blades. In a reaction turbine the steam is expanded in the nozzles AND in the blades, the reaction of the expansion of the steam pushes away from the blades spinning the wheel in the process. The expansion of the steam is necessary to increase its velocity through the turbine.
in a radial flow turbine the steam enters the turbine in the direction of its radius and leaves it in the direction of the axis of the shaft. in a axial flow turbine the steam enters the turbine in the direction of the axis of the shaft and leaves the turbine in the same direction.
steam turbine is multiple shaft euipment, to avoid the viberation of the shaft train runing, the multiple shaft need to be aligned within tolorance. usually, the rim and face run out checked is request.
Steam turbine is when a device that has the extract thermal energy from pressurized steam. It is used to do mechanical work on a rotating output shaft. The steam turbine was invented by Sir Charles Parsons in 1884.
Steam or water, it works the reverse of a fan, where the fan pushes air down, the turbine is turned by the steam or water. there's a shaft leading from the turbine to the generator, which produces the electricity
Thrust bearings are mounted on turbines at or near the end of the shaft, closest to the steam chest (or inlet). This is to maintain the shaft in position with the casing of the turbine, allowing the casing and the shaft to expand evenly together toward the drive end of the turbine.
The Steam Turbine is the one which steam worked pressured Hot and exited then the shaft of the turbine starts to and fro motion due which energy is injected through nozzle in the receiver.
When Turbine shaft temp is below 100 deg.centigrade,Then rolling of turbine carried out it is called cold rolling.
The TSI system is Turbine Supervisory Instrumentation system, consists of multiple instruments, including speed sensors, speed monitors and so on. The system continuously monitors the steam turbines of all important parameters, such as: rotational speed, overspeed protection, eccentricity, shaft vibration, cover vibration, axial displacement, differential expansion, and thermal expansion. The system helps to improve the availability of steam turbine unit.