0
What else can I help you with?
What does RJT mean on a thread?
Ring Joint Type
Why lantern rings in gate valve are used?
Piping hand book decribes that a spacer ring used in the lantern ring type of packing chamer to permit lubrication of the packing, purging of the shaft or stem, or a leak-off system.
What does bearing span mean?
Bearing span is basically the surface area of the inner ring on which the rotor rotates .
What is the maximum possible clearance between shaft with radial O ring and cylinder to hold 5 bar hydrostatic pressure?
It depends on the diameters of the shaft and the O-ring. Whether or not it rotates, or slides, how many O-rings or seals are on the shaft, and the thickness of the cylinder head. Consult the manufacturer of the cylinder for the proper clearances required.
What is a hydraulic slip ring?
Hydraulic slip rings are similar to electrical slip rings and transmit fluid power from a stationary source to rotating parts. The hydraulic slip rings are also known as Fluid Rotary Unions (FRU). Fluid pressure is connected from a stationary tube (the stator) to the rotating parts through either single or multi-ported rotating component (rotor) of the slip ring. Multiple application combined slip rings are also wide used to transport not only hydraulic power but also electrical as well as communication cables through a combined slip ring.
How do you repair valve compression ring 18 hp Briggs stratton?
You don't repair compression rings you replace them.
What is the ring gap on 8 hp Briggs stratton engine?
The ring gap on an 8 HP Briggs & Stratton engine typically ranges between 0.010 to 0.020 inches (0.25 to 0.51 mm) for the top compression ring. It's essential to check the manufacturer's specifications in the engine's service manual, as the exact gap can vary based on the engine model and intended application. Proper ring gap ensures effective sealing and optimal engine performance.
What is the piston ring gap on a 10hp horizontal Briggs stratton engine?
Briggs and Stratton Motor:aluminum cylinder bore compression ring end gap should be no more than .035 inches (.89mm) Oil ring end gap should be no more than .045 inches (1.14mm) Cast iron cylinder bores compression ring end gap should be no more than .030 Inches (.76mm) Oil ring should be no more than .035 inches (.89mm)
What is the end ring gap for a new ring set in a Briggs and Stratton 10 hp engine?
The end ring gap for a new ring set in a Briggs and Stratton 10 hp engine typically ranges from 0.010 to 0.020 inches for the top ring and slightly larger for the second ring. It's essential to measure the gap accurately using a feeler gauge after installing the rings in the cylinder to ensure proper sealing and engine performance. Always refer to the specific service manual for the exact specifications, as they can vary by model.
After replacing valves and rings in my 6.5 Briggs and stratton it smokes real bad What is my problem?
you should have three rings, top ring is the compression ring, second ring seperates the compression ring with the third ring which is the oil ring. check to see if the gaps in all three rings are staggerd if not then you are getting oil blow bye. did you seat your new valves, if not then you may also be getting oil blow bye through the small gap in between the valves and valve seats.
Can a 5.5 Briggs and stratton be convert from a pull start to an electric start. if so how?
Yes, a 5.5 Briggs & Stratton engine can be converted from a pull start to an electric start, but it generally requires specific components. You will need an electric starter motor, a compatible flywheel with a ring gear, a battery, and a wiring harness to connect everything. It's important to check the engine model for compatibility with the electric start kit and follow manufacturer instructions for installation.
How do you replace prime bulb on a Briggs stratton engine?
Very difficult without proper removal and installation tools provided by Briggs and Stratton. The old one can be removed with needle nosed pliers, by gripping as much of the bulb as possible and rocking it back and forth until it pops free. If the bulb tears out, be sure to remove the snap ring holding the base. Be more careful when installing the new one, as it can be torn easily. Put the new bulb in, and snap in the new retaining ring using two small flathead screwdrivers.
Why would an engine have poor compression?
The Cylinder head could be damaged or a ring out of place, causing the release of air, making less compression
What would happen if you only use one piston ring on 80cc bike engine?
If you only use one piston ring on 80cc bike engine, the compression ration will be reduced.
Does the bottom piston ring on a four-cycle engine help control excessive compression?
No, the bottom ring is the oil ring. It wipes excess oil off the cylinder wall.
how many rings are installed in normal SI engine How many rings are installed in normal SI engine?
A typical spark ignition (SI) engine usually has three piston rings per cylinder. These consist of one compression ring at the top, one oil control ring at the bottom, and sometimes a second compression ring in the middle. This configuration helps optimize compression, control oil consumption, and reduce emissions. However, the exact number of rings can vary depending on the engine design and manufacturer.
In a typical automotive engine the piston contains compression rings?
Yes. That is a true statement.
