answersLogoWhite

0

Unified National Fine as opposed to UNC - Unified National Course

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Mechanical Engineering

What are sae screw threads?

S.A.E - Standard American Engineers. Now it is called as UNF i.e. Unified Fine threads.UNF (Unified Fine Thread)Standardised in 1918Angle of Thread 60o DegreesUnified Fine (UNF) and Unified Coarse (UNC).American threads consist of two common and easily obtained thread patterns known as U. N.F and U.N.C. U.N.F [national fine] is exactly the same as the old S.A.E [standard American engineers] that existed before threads were unified.U.N.C [national coarse] roughly derived from the British Whitworth have the same pitches except 1/2 in dia where Whitworth is 12tpi and U.N.C is 13 tpi.Both these threads are 60 degree angleEarly Harley and Indian motorcycles used 24tpi threads on most diameters5/16 and 3/8 UNF are both 24tpi but 1/4 UNF is 28 tpi and a special 1/4 x 24 thread must be used.7/32 x 24 UNC is an obsolete thread. In the late 1960's, when even the U.S. was thinking of going metric, the giant BSA corporation decided it was finally time to scrap the 19th Century Whitworth-based system, and switch to American. Since they had lots of money invested in tooling, the switch wasn't made suddenly (or completely), so bikes and cars from the late '60's and later had a mix of all sorts of thread forms. Typically, engine internals (e.g. the thread on the end of a camshaft) stayed with whatever form it used to have, while simple fasteners (e.g. holding the mud guards on) switched to UNF.


What is the definition of a w.w.unf thread size?

Oh, dude, a w.w.unf thread size is just a fancy way of saying "Unified National Fine Thread." It's like when you go to a fancy restaurant and they call fries "pommes frites." It's basically a standard measurement for screw threads in the United States. So, next time someone asks you about w.w.unf thread size, you can impress them with your knowledge and then promptly forget about it.


Definition of pitch of screw thread?

The pitch of a screw thread is a measure of how closely the threads are spaced. It can be expressed as the number of threads per unit length (32 threads per inch, for example) or as the distance between two threads ( such as .8 mm).


What is the relationship between a nut thread and a screw thread?

when a spiral groove is cut over a hole, then it is nut thread. when a spiral groove is cut over a shaft, then it is screw thread.


What is the largest allowable minor diameter for an M6x1.0 screw thread?

the minor diameter should be between 4.917mm and 5.153 mm, so the largest allowable size is 5.153mm

Related Questions

Can you use unc screws in apart that has unf threads?

No. The coarse thread UNC screws will not thread into the fine thread UNF holes. UNC must be used with UNC and UNF with UNF.


WHAT IS 24 UNF THREAD PLUG GAUGE?

A thread gauge is a tool used for identifying the particular thread on a bolt or screw. The gauge will have several blades with saw like teeth of different sizes. You match a particular gauge to the thread which will then tell you what size thread it is. gauges come in various pitches to match different screw threads. UNF, UNC, Whitworth, Metric etc. Each has a different pitch angle and thread per inch or millimetre.An image of a thread gauge can be seen HERE


What does the 20 represent in a 500-20 UNF-3A thread?

threads per inch


What fullform of UNC nut and bolt?

UNC stands for "UNIFIED BOLT THREAD COARSE" UNF stands for " UNIFIED BOLT THREAD FINE"


How to calculate the best wire size to use with a 10-32 UNF-2A thread?

10-32 unf-2a <<>> The wire size does not need to be calculated. Use a wire terminal end that crimps to the wire. These terminal end come in various wire sizes and bolt hole sizes. Pick the correct end for the wire size you are using and then in that wire size range, pick the correct bolt hole size that fits the bolt.


How can I determine the size of a thread?

To determine the size of a thread, you can use a thread gauge tool or a caliper to measure the diameter of the thread. The size is typically expressed in terms of the thread's pitch and diameter, which can help you identify the thread size.


Full form of UNF?

UNF refers to UnNormalised Form.


What is the camera mount thread size for this particular camera model?

The camera mount thread size for this specific camera model is insert thread size here.


What is the filter thread size for this camera lens?

The filter thread size for this camera lens is insert size here.


What is the Winchester model 90 barrel thread size?

What is the thread size for a Winchester Model 90?


Is it hard to get into UNF?

No.


What is difference between unc tap and unf tap?

unc is coarse, unf is fine pitch