answersLogoWhite

0

There are thousands grades of low carbon steel in the world. The properties (tensile strength) depends of a lot of parameters such as product type, heat treatment, micro-alloying, dimensions of products, etc.

Max possible tensile strength for low carbon steel is 1200 - 1400 MPa.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

What is the tensile strength of aisi 1075 steel?

if its standard wrought carbon steel, the psi should be just about in the 100,000psi range. The last two digits of the designation, 75, are the carbon content. 0.75%. the higher the carbon content, the higher the tensile strength. The ultimate tensile strength of a steel such as AISI 1075 varies depending upon the heat treated condition and hardness. The tensile strength of a steel can be approximated from the hardness using hardness conversion tables found elsewhere on the web.


What is the ultimate tensile strength of mild steel. Show me the stress and strain diagram?

410 n/mm2


What does relation carbon equivalent with tensile strength?

Higher the carbon the steel will have higher TS up to certain point.


What is the tensile strength of mild steel?

Mild steel is a fairly general classification and can cover a considerable variation in material properties. Cold drawn grades in particular will have a higher tensile strength than hot rolled. Something like 400 MPa for yield stress and 500 MPa for ultimate tensile strength is quite common.


What happened to the ultimate tensile and yield strength of most of the metals when temp falls?

building will collapse due to steel failure


What is the ultimate tensile strength of 4335V low-alloy steel sheet?

Find out using knovel like youre meant to.


How do you calculate tensile strength of a ismc 100 channel?

the most effective way to find out is through Westermann Tables....the cross section area of all the standard mechanical manufacturing parts is given..channels.. angles etc....once you know the area and the UTS(ultimate tensile strength) of MS(mild steel)...you know the ans.... help yourself.


What is the tensile strength of 304 stainless compared to carbon steel?

304 strength ranges from 80,000 psi to 250,000 psi, depending on degree of cold work. Standard carbon steel strength is less than 80,000 psi.


What is the strength of the steel?

You mean tensile strength. Different steels have different tensile strengths. The way they are made (drawn, cast, forged, etc.) is critically important to the tensile strength. By the way--steel is more important for its stiffness than its tensile strength.


What is the tensile strength of En 8?

EN8 is an unalloyed medium carbon steel with good tensile strength. It is normally supplied in cold drawn or as rolled. Tensile properties can vary but are usually between 500-800 N/mm2


Give you a example of tensile strength?

Take a piece of any material, say a steel rod, or a piece of timber dowel and you grip it at both ends and try to pull it until it breaks. When you do this, you are putting a tensile load on the material. It is said to be 'in tension'. If the material had a cross sectional AREA of say, 1 Square Inch, and the Tensile Load on it was say, 50,000 Pound,then the Tensile load would be 50,000 PSI (pound per square inch). If the material broke apart under that exact load, then we say it has a TENSILE STRENGTH of 50,000 lb/ square inch. Engineers measure tensile strength in either Pound/Squ.inch. OR Pascal. A Pascal (metric system) is Newton per Square Metre. Steel cables used on bridges have a Tensile Load on them at all times. Engineers calculate the cross sectional area of steel cable needed to be safe , and never break apart. Engineers need to know the Tensile Strength of Steel to be able to choose what size cable to use,so that it is quite SAFE and will not break when in Tension. They use safety factors such as 5 (typical) This means they calculate the cross sectional area of a cable which is going to be 5 times as strong as the Tensile Strength of the steel they are using. They then know that it will never break. The Tesile strength at which a material breaks is called its Ultimate Tensile Strength. Engineers never allow the tension in steel to exceed about 1/5th ofthe Ultimate tensile strength of the steel. Modern Steel bars used in steel structures, has an ultimate tensile strength of approx. 80,000 lb/Squ.inch


What is yield stress value for frp?

3000 MPa ultimate tensile strength (more than 10 times mild steel)