0
What else can I help you with?
What is a hydraulic check valve do?
A hydraulic check valve is a device that allows fluid to flow in one direction while preventing backflow in the opposite direction. It operates automatically based on fluid pressure, opening to permit flow when pressure is present in the forward direction and closing when there is reverse flow. This function is crucial for maintaining system pressure, protecting equipment, and ensuring efficient operation in hydraulic systems.
Why lantern rings in gate valve are used?
Piping hand book decribes that a spacer ring used in the lantern ring type of packing chamer to permit lubrication of the packing, purging of the shaft or stem, or a leak-off system.
What is the most expensive element in use?
It's difficult to answer this question specifically due to ever changing prices and the difficulty in getting information on certain elements. By far however the transuranic elements are the most expensive because of production and permit costs. Plutonium can cost around $4,000/gram and Californium can cost $10/mg or $10,000/gram.
What is a machinists V block?
A machinists V block in its simplest form is a block of metal with a V shaped (usually 90 degree V ) groove cut into it ( typically with a small square notch at the bottom of the V running its full length ) It is machined with high precision and usually hardened to prevent excessive wear. It is used to hold materials such as round bar securely while machining it. Imagine placing a round bar on a flat surface and trying to hold it while you try to drill a hole through it. the block may have other grooves to permit secure attachment to the work surface and also to accommodate a horse show shaped clamp to hold the work in in the V
Start-up procedure of pump commissioning?
Check pump: Maintenence: Done, work permit close, and power back from Substation. Panel: There is no alarms. Inform: Inform DCS Operator before start up the pump and be on touch with Control room. Level: Check Level, must be over Low level. if you start pump with low level or without level Cavitation will happen, but now almost all pumps have an Interlock device tp protect it and won't start in Low Level. Be sure: Discharge Valve Must be fully close before start pump, To avoid Motor Over current, and Suction valve must be fully open. Open Vent and wait to fill pump casing until the flow comes out without air, then close vent. Now you are ready to start pump but the important thing is to inform DCS operator that you finished the priming, then push Start Putton. After pump runing Check abnormal sounds or Hi vipuration and Discharge Pressure if every thing OK now Inform DCS Operator to Open Discharge Vale, then open it Gradually. I hope these can help you.... With my best, Ibrahim Sulaiman ibrahim.sulaiman@hotmail.com
Items you can buy with a farm tax permit?
A farm tax permit allows the purchase of farm machinery or equipment.
What is equipment data?
Data Terminal Equipment (DTE)A Data Terminal Equipment (DTE) is a communication device that is the source or destination of signals on a network, typically a terminal or a computer. It communicaties with the data circuit-terminating equipment and can perform all the required functions necessary to permit users to communicate.
Is the computer a data terminal equipment?
Data Terminal Equipment (DTE)A Data Terminal Equipment (DTE) is a communication device that is the source or destination of signals on a network, typically a terminal or a computer. It communicaties with the data circuit-terminating equipment and can perform all the required functions necessary to permit users to communicate.
Is heavy equipment certification a stae level or federal level certificate?
It is a state level license or permit.
What is cable glanding?
A device designed to permit the entry of a cable into an electrical equipment and which provides sealing and retension. Cable well tightened with supporting of cable holding material into an electrical equipment or panels.
Is it legal to drive a mini bike on the street with a permit?
No, It's not whether you do, or don't, have a permit. It's the safety equipment, or lack thereof, that makes that class of vehicle unlawful to operate on the street.
What should you do when hauling equipment that is wider, heavier, or longer than the law permits?
Should obtain an oversize/ overweight permit from the Texas Department of Transportation permit office .
Do you have to pull an electrical permit for a job when the materials are less than 100?
In Canada every electrical installation requires a permit. The minimum cost for a new installation permit is $40.00. Maintenance of existing equipment requires no permit. For larger installations the price of the permit is based on the cost of the electrical job. Ten years ago if the new installation was under 500 dollars it did not require a permit. As government agencies now become privatized, the new companies that are taking over for the government are looking for ways of getting more and more dollars out of the general public. How does the saying go "Squeeze the public until they squeal, then back off a half a turn".
What type of garage remodeling jobs do I need a building permit for?
You do not need a building permit if changing the interior of the garage. If you are using heavy machine equipment and moving large lumber on the outside of the garage to make changes then a building permit is required.
What equipment did they need for the gold field?
Blankets, tent and bedroll Pick Pan Bucket Cradle Spade Windlass Gold Digging Permit
What are the isolation and lock-off procedures or permit-to-work procedure that applies to the equipment being installed or commissioned?
Isolation and lock-off procedures involve ensuring that all energy sources to the equipment, such as electrical, mechanical, hydraulic, or pneumatic, are fully de-energized and secured. This typically requires the use of lockout/tagout (LOTO) devices to prevent accidental re-energization while maintenance or commissioning work is performed. A permit-to-work system may also be implemented, which outlines specific safety measures, necessary risk assessments, and authorization processes that must be followed before work can commence. These procedures are crucial for ensuring the safety of personnel and preventing accidents during installation or commissioning activities.
What are the control measures that can be used to eliminate the hazard?
Some control measures that can be used to eliminate or reduce hazard include: lock off and permit to work procedures, provision of safe access and egress, use of guards and fumes extraction equipment, use of personal equipment.
