0
What else can I help you with?
How do use a strap wrench?
You wrap it around an oil filter or something then hold the strap as you pull the lever back. If it doesn't seem to work at first, just flip it over and try the other way. It's a little tricky at first.
What is the density of 301 stainless steel?
301 stainless density values seem to vary according to the supplier data sheets, from 7.88 g/cc, (AK Steel) to 8.03 g/cc, (Allegheny Ludlum). I guess the key factor in answering this enquiry is identifying the accuracy required.
What is an air-conditioner?
An air conditioner is any type of device that helps moderate temperature indoors. An air conditioner does not have to be a cooling system, technically a heater is also an air conditioner, though most people seem to only consider air conditioners (sometimes referred to as A/C units) machines that lower the temperature to a user defined temperature. An air conditioner is a machine that filters/ventilates out hot air and cools the inside of a room or building. Air conditioners come in many varieties, ranging from wall-mounted units to portable units.
How are loads transmitted to the ground?
Loads are not really transmitted to ground. Yes, there is parasitic induction due to capacitive coupling, but the return path for the hot conductor(s) is(are) another hot conductor(s) or neutral. While neutral is grounded, it is essentially a single point connection and, by Kirchoff's current law, has little or no current through ground. It would seem that this is contradicted by the wye connection because, ultimately, neutral is grounded, making the ultimate return path to be ground. In fact, however, looking at the big picture, each leg in the wye connection is balanced, so it looks like a delta connection. Unless there is some fault, the net current on ground, as seen by the substation transformer, and by the earth ground between it and the service drop, is nominally zero.
What is the difference between GRE pipes and GRP pipes?
Glass-reinforced plastic (GRP) is a composite material or fiber-reinforced plastic made of a plastic reinforced by fine fibers made of glass. Like carbon fiber reinforced plastic, the composite material is commonly referred to by the name of its reinforcing fibers (fiberglass). The plastic is thermosetting, most often polyester or vinylester, but other plastics, like epoxy (GRE), are also used. The manufacturing process for GRP fiber glass uses large furnaces to gradually melt the sand/chemical mix to liquid form, then extrude it through bundles of very small orifices (typically 17-25 micrometres in diameter for E-Glass, 9 micrometres for S-Glass). These filaments are then 'sized' with a chemical solution. The individual filaments are then bundled together in large numbers to provide a 'roving'. The diameter of the filaments, as well as the number of filaments in the roving determine its 'weight'. This is typically expressed in yield-yards per pound (how many yards of fiber in one pound of material, thus a smaller number means a heavier roving, example of standard yields are 225yield, 450yield, 675yield) or in tex-grams per km (how many grams 1 km of roving weighs, this is inverted from yield, thus a smaller number means a lighter roving, examples of standard tex are 750tex, 1100tex, 2200tex). These rovings are then either used directly in a composite application such as pultrusion, filament wounding (pipe), gun roving (automated gun chops the glass into small lengths and drops it into a jet of resin, projected onto the surface of a mold), or used in an intermediary step, to manufacture fabrics such as chopped strand mat (CSM) (made of randomly oriented small cut lengths of fiber all bonded together), woven fabrics, knit fabrics or uni-directional fabrics. An individual structural glass fiber is both stiff and strong in tension and compression -- that is, along its axis. (Although one might intuitively imagine the fiber to be weak in compression, it is actually only the long aspect ratio of the fiber which makes it seem so; i.e., because a typical fiber is long and narrow, it buckles easily.) On the other hand, the glass fiber is unstiff and unstrong in shear -- that is, across its axis. Therefore if a collection of fibers can be arranged permanently in a preferred direction within a material, and if the fibers can be prevented from buckling in compression, then that material will become preferentially strong in that direction. Furthermore, by laying multiple layers of fiber on top of one another, with each layer oriented in various preferred directions, the stiffness and strength properties of the overall material can be controlled in an efficient manner. In the case of glass-reinforced plastic, it is the plastic matrix which permanently constrains the structural glass fibers to directions chosen by the designer. With chopped strand mat, this directionality is essentially an entire two dimensional plane; with woven fabrics or unidirectional layers, directionality of stiffness and strength can be more precisely controlled within the plane. A glass-reinforced plastic component is typically of a thin "shell" construction, sometimes filled on the inside with structural foam, as in the case of surfboards. The component may be of nearly arbitrary shape, limited only by the complexity and tolerances of the mold used for manufacturing the shell.
Are most men uncomfortable receiving massages?
yes and no, I myself, as a male massage therapist believe that most men are much more comfortable with receiving a massage from a female massage therapist than a male massage therapist. men seem to react to massage as an intimate situation , not many think of it as a medical option for injury or stress.
Is BestMassage a good brand for massage tables?
not sure,it seem the massage table suits for yourself is the most important:-) i always use this massage table,you can have a try:http://www.aosom.com/soozier-black-portable-massage-table3-fold-thick_p76.html
What is best branch in polytechnic engineering?
The best branch for B tech is going to be what is more interesting to you. Mechanical Engineering and Aeronautical Engineering seem to be in favor right now, with mechanical in the lead.
Are most massage chairs used in homes?
I couldn't easily find statistics on this, but given the environments used in product ads for massage chairs, manufacturers seem to be targetting the residential market.
How do you put converging in a sentence?
Worlds are converging!The greyhounds seem to think that they are converging on the mechanical rabbit.
Who introduced mechanical looms to England in 1680?
1680 does not seem to be the correct time frame for this. See the link I will place below.
What is a lingam massage?
The phrase “lingam massage” has entered the public eye as a type of genital massage with Hindu influences, it doesn’t literally translate to the male reproductive organ. Lingam is actually a representation of the Hindu god Shiva, which happens to be phallic in shape. You can understand why it has come to mean penis to so many people. However, some Hindu practitioners still strongly associate the concept with Shiva. To them, using the word as part of the phrase “lingam massage” might seem offensive because it reduces the meaning.
What methods did Gaines utilize that made the story of Jane Pittman seem so real?
I know that dialect was one
How does new technology affect massage therapists?
They didn't seem to go hand in hand before - this company is trying to ease the transition from pencil and paper to a simple online tool! Check out: www.theappoutfitters.com - they just developed "MassageApp" to make the lives of Massage Therapists a little bit easier!
What is a 4 hand massage?
From the word four hands it means four hands are going to massage your whole body, and to make that possible, since there is no body with four hands, two people are going to do this task, which is a new experience to those who have not yet tried this. I have read about this from an article which seem reliable at http://tantricparadise.co.uk/
Who has more Mario or sonic?
You seem to have forgotten to ask who has more of what.
What is the primary way to add clients in a massage business?
The business strategy is to have one thousand business cards and hand them out to people you meet everyday; at the grocery store, in line at the bank, anywhere. And, then expect that one in ten respond, and one in ten that respond will book a massage with you.The other way to get clients is to network with other massage therapists. Get a group of massage therapists together and have each give out 100 cards to other therapists. Then encourage them to refer to you, because you will reciprocate and refer some of your clients to them. This system works best if you all have different specialties. In the long run, you will all end up with more clients. It may seem like a strange idea, but it works!
