0
You can use the type of hinge that is a screw threaded bolt that the gate sits on. You would just have to drill the pilot holes in the right place and angle. If using a strap hinge, you can either shim behind one or chisel out a groove for the hinge to sit in. Without seeing it, it's hard to give specifics on how to do it. Set the gate in the opening and see what it takes to make the hinges you want to use work.
What else can I help you with?
How can I install a chain link gate?
To install a chain link gate, start by measuring the opening and purchasing a gate that fits. Dig post holes, set the gate posts in concrete, and attach the gate hardware. Hang the gate on the posts and adjust for proper alignment. Finally, secure the gate in place and test its functionality.
How to hang a gate properly?
To hang a gate properly, follow these steps: Measure and mark where the gate will be installed. Dig holes for the gate posts and set them in concrete for stability. Attach hinges to the gate and then to the gate posts. Install a latch or lock for security. Adjust the gate to ensure it swings smoothly and securely. By following these steps, you can hang a gate properly.
What holds up the gate?
post
What are the best installation techniques for a metal post for a gate?
The best installation techniques for a metal post for a gate involve digging a deep and wide hole, setting the post securely in concrete, ensuring it is plumb and level, and allowing the concrete to fully cure before attaching the gate. This provides stability and durability for the gate post.
My neighbor fixed his gate to my fence can I remove it?
His gate really jars my fence when he shuts it. I think he should put his own post in and attach his own gate to his own post.
Where is the twisted lamp post in Fantage?
at the castle only on fools day then it is just a lamp post
What are the necessary materials and steps required to construct a sturdy gate fence post for a residential property?
To construct a sturdy gate fence post for a residential property, you will need materials such as pressure-treated wood posts, concrete mix, gravel, screws, and a gate latch. The steps involved include digging a hole for the post, setting the post in concrete, adding gravel for drainage, and attaching the gate to the post securely.
Can you hang a bag on a malibox or post?
You cannot hang anything on any part of the mailbox itself. Hanging items from the post beneath it is allowed.
How do you install vinyl fencing?
Hi! We have an easy to use Vinyl Fencing planning and installation guide that you might find helpful, view it here: http://www.fenceauthority.net/fa_phelp.asp The basic installation instructions include: 1. Dig post hole. 2. Insert appropriate post into hole (Figure 1). 3. Slide the fence-section rails into the pre-punched post (Figure 2). 4. Fill post-hole with concrete. 5. Secure with enclosed screws. 6. Plumb and level the posts and pickets while the concrete is setting. Brace the post as necessary while concrete sets. 7. Hang gate(s) to appropriate gate post(s). 8. Attach any gate or post hardware and/or fence accessories.
A word that goes with these 3 words keeper post and house?
Gate Gatekeeper an attendant at a gate who is employed to control who goes through it. Gatepost a post on which a gate is hinged, or against which it shuts. Gatehouse a house or enclosure near a gateway.
What is the purpose of the gate latch bolt and how does it function in securing a gate?
The purpose of the gate latch bolt is to secure a gate by preventing it from swinging open. It functions by sliding into a corresponding hole or catch on the gate post, effectively locking the gate in place.
Eight foot gate how far apart do you place the posts for the gate?
Metal Gate & Posts: 96 inches plus 3 inches for barrel hinge plus 1 inch for clearance at non hinged post if hinge is mounted INSIDE between the posts. If a flat hinge is flat mounted on outside of post and gate, instead of 3 inches, use the width of the hinge ferrell (the raised ridge in the middle where the two sides of the hinge pivot).Wooden Gate & Posts: Same.If the hinges are mounted inside between the posts the above distances will let the gate swing 90 degrees or slightly less depending on the thickness of the post and the gate material. If you want to have gate swing a little further, either mount barrel hinges toward one side of the post or increase the hinge distance from 3 inches to a distance sufficient to permit the edge of the gate to clear the width of the post as it opens.
