answersLogoWhite

0

If it's silicone, as is likely, then get most of it off with a sharp edge of a craft knife and the rest with acetone or lacquer thinner on a rough rag.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How can you remove glue from fiberglass bathtub?

You have to NAME the glue before we can answer that.


Is there fiberglass in gorilla glue?

NO, Gorilla Glue is a form of polyurethane.


How do you remove PVC glue from fiberglass tub?

To remove PVC glue from a fiberglass tub, start by carefully scraping off as much of the glue as possible using a plastic scraper or a credit card to avoid scratching the surface. Next, apply a solvent like acetone or rubbing alcohol to a soft cloth and gently rub the affected area, ensuring proper ventilation. Always test the solvent on a small, inconspicuous area first to ensure it doesn't damage the fiberglass. After removal, clean the area with mild soap and water to remove any residue.


Can you tile a fiberglass shower curb I am having a glass door and pane installed and discovered that the fiberglass is stained and would show under the door I have left over tile?

You can if you use a tile glue suitable to the fibreglass. Read the instructions on your adhesive carefully, many will stick to fibreglass,but some won't.


How do you remove the drivers side door trim to access the electric window motor?

Hi, i have a W reg Renault Megane and recently had to put a new door on. I had to remove the interior from the old door and put it on the new door. To remove the interior from the door you need to remove all the screws (including from behind the speaker cover). Once this is done the door card will not budge. The whole door card is glued on with an incredibly strong adhesive. I used a hacksaw blade to gently remove the glue. The glue is only on the bottom half of the door card. Make sure you are incredibly careful when removing the glue because you need to prise the plastics back slighly to gain access to the glue. Good luck it took me ages. I found after unscrewing all observable screws I still could not prise the door off, a friend pointed out that the door handle (used to close the door not door lever to open it) needed to have the cover removed as there were another two screws under there. I did not find the glue a problem as it was quite worn.


Can you glue a piece of wood to fiberglass with epoxy glue?

Yes you can, if done properly it is very effective.


How can I fix door hinge holes effectively?

To fix door hinge holes effectively, you can use wooden dowels and wood glue. First, remove the hinge from the door and fill the holes with wood glue. Then, insert wooden dowels into the holes and let the glue dry. Once the glue is set, trim the dowels flush with the door surface and reattach the hinge. This method provides a strong and durable fix for door hinge holes.


How do you remove a staircase?

To remove a staircase you will first have to remove the posts, and the rails. Use a drill to remove the screws, and then use a putty knife to break pry the glue away from the pieces. Remove the bolt that attaches the rail to the stud. Remove the carpet or stair treads. Remove the frame along the steps.


How do you remove glue stains dropped on a fiberglass tub when installing plumbing?

It would help immensely if you said WHICH glue made the stains. As this was during plumbing, it may have been yellow ABS Glue, in which case your best remover is Whitlam's Glue Wash. -Rub the stains with a rag dipped in this and they should soften and come off -IF it's ABS glue.Next time please -Name your Glue -


What would be the best way to fix a decorative reindeer?

Super glue or epoxy make the best Christmas repairs. Since reindeer are made of fiberglass the epoxy rebonds the fiberglass with one another. Super glue is another alternative.


How do you remove adhesive door handle covers from vehicles door handles?

peel them off and carefully use wd-40 to clean away any glue left behind


How do you remove plastic wrapping from a door?

You might try a hair dryer , sometimes being warmed up will release the glue better.