0
What else can I help you with?
How many shingles to cover 128 sq ft?
You are going to need 4 bundles. 3 bundles equals a square and a square equals 100 square feet.
How many sq' of shingles is needed to do a 30'x50' house?
A 30x50 roof has 1,500 square feet which is 15 squares. 3 bundles of shingles equals 1 square so you will need about 45 bundles.
How many bundles of shingles to cover 1600 sq ft roof?
3 bundles to a square and 100 sq. ft. in a square, so 3 times 16 equals 48. Depending on how much roof edge and peak add a couple bundles for starter strip and the cap.
How many bundles of architecture shingles equals one square is it the same as 3 tab?
Usually 4 that information should be on the bundle
How many bundles of shingles will cover 800 square feet?
To determine how many bundles of shingles are needed to cover 800 square feet, you first need to know the coverage area of a single bundle. Typically, one bundle of shingles covers about 33.3 square feet. Therefore, to cover 800 square feet, you would divide 800 by 33.3, which equals approximately 24 bundles. It's advisable to purchase a few extra bundles to account for waste and any mistakes during installation.
How many bundles of shingles will you need 1406 feet?
That would depend on the amount of square footage covered per bundle, a figure that can vary. Tell the supplier that you need enough shingles to cover 168 square feet, or check the information on the back of the bundle which will describe the bundle's coverage.
How many bundles of shingles for 384 square ft of roof?
Measure the area to be covered carefully and take into consideration the clope of the roof. Roofing materials are measured by the "square" instead of using "square feet" and the number of bundles will depend on the type of shingle that you are planning to use. A "square" equals one hundred square feet, so you are looking at four squares of shingles (including sixteen square feet of waste which is about right). Standard asphalt shingles of average weight require three bundles per square so if using this type of material you would obviously purchase twelve bundles. However, if you are using the more attractive and longer-lasting dimensional shingle, this material require four bundles per square and your needs would be sixteen bundles. These shingles also require twice as many nails and the warranty from the manufacturer is void if you use fewer nails or staples. Also consider using thirty pound felt instead of the usual fifteen pound felt commonly used to save money. In the long run the roof will last longer with the thicker felt and thirty pound felt is actually easier to install than its lighter cousin due to the fifteen pound felt's tendency to tear during installation. landcranch
How many shingles will cover 60 sq ft?
depends on where you buy them and the size of the pack. at Lowe's, three packs of shingles usually equals 100 square feet, so your answer would be two packs of shingles considering you should always buy 10% more then you need, just in case.
What is a square of roofing?
Well, honey, a square of roofing is a unit of measurement used in the roofing industry. It equals 100 square feet of roof area. So, if you're planning on getting some work done on your roof, you better know how many squares you're dealing with.
How many squares is 80 square metres?
I assume you are refering to roofing material, since a "square" in the roofing industry is equivalent to 100 square feet of material. 1 linear meter equals 3.28084 feet 1 square meter equals (3.28084 ft)2 or 10.7639 square feet Therefore, 80 square meters equals 80 x 10.7639 square feet or 809.93 square feet Since a roofing "square"=100 sqft, 80 square meters equals 8.0993 "squares" If you don't want to carry a calculator around in the field, just remember that: 1 square meter is a bit under 11 square feet. and that 1 square of roofing will cover almost 10 square meters (but not quite) Rod Burrows, PE
Advantages of fiber bundles over single fiber?
Fiber bundles allow for increased throughput by aggregating multiple fibers in a single cable, providing redundancy in case of failures, and offering scalability for future network expansion. Additionally, fiber bundles can simplify installation and maintenance processes compared to managing individual fibers.
How many square shingles for a 28X52?
To calculate the number of square shingles needed for a 28x52-foot roof, first determine the total area by multiplying the length by the width, which equals 1,456 square feet. Since one square of shingles covers 100 square feet, divide the total area by 100. Therefore, you would need approximately 14.56 squares of shingles, rounding up to 15 squares to ensure complete coverage.
