0
What else can I help you with?
What simple machine are in motorcycle?
The wheel and axle and the gear, which is similar to the wheel and axle.
What are the front and rear axle nut torque specifications for a 2003 Honda XR100 motorcycle?
Front axle = 55 lbf-ft. Pinch bolts = 9 lbf-ft. Rear axle = 80 lbf-ft.
Will a shaft drive motorcycle engine be able to run a 4 wheeler type axle?
Yes, a shaft drive motorcycle engine can potentially run a 4-wheeler type axle, but it would require significant modifications. The engine's output would need to be adapted to drive the axle effectively, as motorcycles typically have different torque and power characteristics compared to automotive engines. Additionally, the shaft drive mechanism must be compatible with the axle's design, which may involve custom fabrication. Overall, while feasible, it involves complex engineering challenges.
Is it safe to ride harley fatboy with missing axle cap?
Riding a Harley Fat Boy with a missing axle cap is not safe. The axle cap helps secure the wheel and prevent debris from entering the axle area, and its absence can lead to increased wear or potential wheel failure. It's best to replace the missing axle cap before riding to ensure safety and proper functioning of the motorcycle. Always prioritize safety and maintenance to avoid accidents.
What is the length of rear axle for a 1977 Harley Davidson Sportster motorcycle?
The length of the rear axle for a 1977 Harley Davidson Sportster is approximately 3/4 inch in diameter and typically around 10.5 inches long. However, variations can occur depending on specific models and modifications. For precise measurements, it's advisable to consult the motorcycle's service manual or reach out to a Harley Davidson dealer.
What is a motorbike yoke?
The yoke's(!) on a motorcycle is the two plates of wich the front-telescopes, as well as the steering-axle, gets through. The handlebar are traditionally mounted on the upper yoke!
How do you take off wheels off a Honda shadow vlx 600?
To remove the wheels from a Honda Shadow VLX 600, start by securely lifting the motorcycle using a stand. For the front wheel, loosen the axle nut and remove the front brake caliper, then slide the axle out. For the rear wheel, loosen the axle nut and the rear brake caliper, then adjust the axle adjusters before sliding the axle out. Ensure to support the bike properly and follow safety precautions throughout the process.
How do you remove the front axle on a 2004 Honda shadow 600 vlx?
To remove the front axle on a 2004 Honda Shadow 600 VLX, start by securing the motorcycle on a stable stand. Loosen the axle pinch bolts on both sides of the front fork, then use a socket wrench to remove the axle nut on one side. Slide the axle out from the opposite side, ensuring that the brake caliper and wheel are supported during the process. Finally, carefully detach the front wheel from the forks.
How do you change a rear tire on a Yamaha XS1100?
with the motorcycle on the ground install tire change tool from tool kit across the tabs on the frame then put motorcycle on center stand. Remove rear fender bolts to raise rear fender, remove axle bolt then remove rear tire.
What is the rear axle torque for a 2007 Honda shadow spirit motorcycle?
The rear axle torque specification for a 2007 Honda Shadow Spirit motorcycle is typically around 50-55 foot-pounds (68-75 Nm). It's important to consult the owner's manual or a service manual for precise specifications, as torque values can vary slightly based on specific models and configurations. Always ensure that the correct torque is applied to maintain safety and performance.
How many axles on a motorcycle?
That depends on how many wheels the motorcycle has. Technically if it has two wheels, then it has two axles. Every wheel has its own axle. But some people would say that if the wheels are parallel to each other then that would count as one axle, like in a ragular car with four wheels.
What is the torque spec for the rear axle nut on a 79 gs550?
The torque specification for the rear axle nut on a 1979 Suzuki GS550 is typically around 65-75 ft-lbs (88-102 Nm). It's important to ensure that the nut is properly torqued to maintain the integrity of the rear axle and ensure safe operation. Always consult the specific service manual for your motorcycle for the most accurate and detailed information.
