0
To do this, you need to remove the front pulley. Unscrew & slide the the bolt out of the front pulley. The front is made up of 2 halves spindle sheaves. You may need to remove also the front wheels to make room. When installing the new belt, you need to stand up the edger to rest the edger's front on the ground to compress the spring in order to have room to insert the new belt. Start from the engine pulley, wrap the belt onto the 2 idle pulleys. The "V" side needs to be onto the top idle pulley & the 'Flat' side needs to be onto the bottom idle pulley (this is important belt pattern). Then turn the belt 90 degrees counterwise from the bottom idle pulley & wrap the "V" side onto the front pulley. While the belt is onto the front pulley, insert back the bolt into the front pulley to install the front pulley. Put everything back together & that is it. Looks hard but really simple. The user manual is not clear on this. The belt MTD part number is 754-04032B. Hope this helps. Good luck. User manual on this site. http://manuals.mtdproducts.com/mtd/DocGetter?doc=769-00527h.pdf JoeJoe
What else can I help you with?
How do you tighten a belt on a golf car?
There is no belt adjustment on a golf cart. However, if the belt is too loose, it may be a drive clutch problem, and an adjustment to the clutch can be made.
How do you adjust clutch belt on 89 Yamaha g2 golf cart?
you cant adjust a drive belt, you problem is in the secondary clutch, I am sure you need to replace the sliding clutch and put a spacer in front of the hub.
How do you tighten the air conditioning belt 1988 BMW xi?
Sepentine-replace tensioner,v-belt, adjust accessory and tighten.
Tighten fan belt on a Renault master?
To tighten the fan belt on a Renault Master, a person needs to adjust the belt tension wheel. This wheel has a bolt that is inserted in a groove. The bolt can be loosened and then moved to the desired location to tighten the belt.
How do you change a belt on a Suzuki vinson?
you have to take the primary clutch off and start the belt on the secondary and use the sleeve on the primary to walk the belt on the primary shaft. Then reassemble the clutch and tighten down the nut. simple..
How do you adjust the transmission belt on a 2001 polaris scrambler 500 4x4?
To adjust the transmission belt on a 2001 Polaris Scrambler 500 4x4, first, ensure the vehicle is on a flat surface and the engine is off. Remove the clutch cover by unscrewing the retaining screws, then check the belt's wear and tension. If the belt is worn, replace it; otherwise, adjust the belt by loosening the clutch mounting bolts and repositioning the clutch for proper tension. Finally, reattach the clutch cover and ensure everything is secure before testing the vehicle.
How do you adjust air con clutch on 1989 jeep Cherokee?
There is no adjust on an AC clutch, it is a good or bad situation. The clutch is activated magnetically. If it is th ebelt you are asking about it should be kept tight by the belt tensioner. If it is still squealing, change the belt, if no help change the tensioner.
How can I adjust a belt properly?
To adjust a belt properly, first locate the belt tensioner and use a wrench to loosen it. Then, adjust the belt tension by moving the tensioner until the belt has the right amount of tension. Finally, tighten the tensioner back up and make sure the belt is aligned properly on the pulleys.
Where is the AC tension pulley for a 2000 Chevy Metro?
you dont adjust a tension pulley you adjust the position of the compressor to tighten the belt
How to adjust a belt properly?
To adjust a belt properly, first loosen the buckle and slide it to the desired position. Then, tighten the belt to ensure a snug fit around your waist or hips. Make sure the belt is not too tight or too loose, and adjust as needed for comfort and security.
How do you adjust a new drive belt for a 1538 hydro Sabre lawn tractor?
Need to tighten the belt on john Deere 1538
Adjust a drive belt on a 1999 325 polaris trail boss?
the belt is adjusted by adding or removing shims in the secondary clutch. to tighten the belt you remove or use thinner shimms. not a hard job after you figure it out, but not easy if you've never done it. if you have never done it i suggest having someone who has help you the first time. there are also a few specialty tools you will need, puller and clutch compressor.
