on the bottom of the engine there is a drain plug just like a car if you have a skid plate you might not be able ti see it but its there you do not have to take the skid plate off there is a hole and the oil filter is on the side of the engine usually three 8mm bolts just that little cover comes off
To change the oil in your 2004 Honda Rancher ES ATV, start by warming up the engine slightly to thin the oil for easier drainage. Turn off the engine, then place a drain pan under the oil drain plug and remove the plug to let the old oil drain completely. Replace the drain plug, then remove the oil filter and replace it with a new one if necessary. Finally, refill the engine with the recommended oil type through the dipstick tube, checking the level as you go to ensure it’s at the correct mark.
Honda says after 10 hours! But go by the color of the oil. Oil dosent get old, it gets dirty. So when its black chang it.
On a 1999 Honda FourTrax ATV, the oil drain plug is located on the bottom of the engine, typically on the left side. It is a hexagonal bolt that you can access easily from underneath the ATV. Make sure to place a drain pan underneath it before removing the plug to catch the old oil. Always refer to the owner's manual for specific details and maintenance guidelines.
On a 2004 Honda Rubicon ATV, the oil filter is located on the right side of the engine, just below the rear cylinder. It is typically positioned near the oil drain plug, making it accessible for maintenance. To change the oil filter, you'll need to remove the old filter and replace it with a new one, ensuring to check for any oil leaks afterward.
The oil drain plug for a 2000 Honda Rancher 350 is located on the bottom of the engine's oil pan. You'll find it towards the rear of the engine, typically on the left side when facing the front of the ATV. To access it, you may need to lift the ATV or place it on a level surface, and then use a wrench to remove the plug for oil drainage. Be sure to have a container ready to catch the old oil.
To change the rear wheel bushing on a Honda Rancher ATV, first, elevate the rear of the ATV and secure it on jack stands. Remove the rear wheel by loosening the lug nuts and taking off the wheel. Then, take out the axle and carefully remove the old bushing from the swingarm. Finally, install the new bushing, reassemble the axle and wheel, and ensure everything is tightened properly before lowering the ATV.
On a 2004 Honda Rancher, the oil filter is located on the right side of the engine, near the bottom. It is typically positioned above the oil drain plug and can be accessed from the side of the ATV. To replace it, you'll need to remove the old filter and install a new one, ensuring to follow the manufacturer's specifications for oil type and capacity.
To change the gear oil on a Chinese 125cc ATV, first locate the gear oil drain plug, usually at the bottom of the transmission case. Remove the drain plug and allow the old oil to completely drain out. Once drained, replace the drain plug and refill the gear oil through the fill plug, using the recommended type and amount of oil specified in the owner’s manual. Finally, check for leaks and ensure the oil level is correct before taking the ATV for a test ride.
To change the oil on a 2005 Honda Foreman ES 500, first ensure the ATV is on a level surface and warm up the engine slightly for better oil flow. Remove the drain plug located at the bottom of the engine and let the old oil drain completely into a pan. Replace the drain plug, then remove the oil filter and install a new one. Finally, fill the engine with new oil through the dipstick tube, using the recommended oil type, and check the level to ensure it's within the proper range.
Drain the old and add the new...use SAE 10-40
For a 2000 Honda Rancher ATV, the fluids that need to be changed include engine oil, which should be replaced regularly to ensure optimal performance, along with the oil filter. The transmission fluid also requires periodic changes to maintain proper shifting and lubrication. Additionally, the coolant should be checked and replaced if it's old or contaminated, and the brake fluid should be inspected and changed if necessary. Regular maintenance of these fluids is essential for the longevity and efficiency of the ATV.
Type in How do you change oil? as your question for some basic advice. For me, it's cheaper to look in the Sunday paper and clip out a coupon then it is to buy the parts and deal with proper disposal of the old oil and filter.