0
What else can I help you with?
Skidoo how to drain gas?
To drain gas from a Skidoo, first ensure the snowmobile is on a level surface and the engine is cool. Locate the fuel shut-off valve and turn it off, then disconnect the fuel line from the carburetor or fuel pump, allowing the gas to drain into a suitable container. You can also remove the fuel tank cap and siphon the gas out if necessary. Always follow safety precautions, such as working in a well-ventilated area and avoiding open flames.
Why does your carboraters keep freezing up on your skidoo?
Carburetors can freeze up on a Skidoo due to moisture buildup inside the carburetor, which then freezes in cold temperatures. This can be exacerbated by snow ingestion or prolonged exposure to cold, wet conditions. Ensuring the carburetor is properly insulated and protected from moisture, as well as using fuel additives designed to prevent freezing, can help prevent this issue.
How do you drain the carburetor on a Yamaha Grizzly450?
Very carefully
Does the soil drain well in the tundra?
no, there are bogs and frozen earth in the tundra due to poor drainage
Where is the coolant drain plugs on a Toyota Tundra V8 engine?
There are 3 drain plugs on the Toyota Tundra V8 engine and radiator. On the radiator petcock, the plastic thumbscrew, and drain valves are on the bottom, driverâ??s side of the radiator.
How do you drain fuel from 1993 Yamaha virago 1100?
pull the gas line off of the carburetor and let it drain.
What is the best method to clean out evaporator drain on 2008 Tundra?
Vacuum
What is the best snowmobile?
Skidoo xp 800
How do you clean the carburetor on a 2002 Honda vlx 600?
Although I cannot be specific with this make and model, this trick has worked on numerous vehicles over the years. Disconnect the fuel line and unscrew the drain plug, which is located on the side or bottom of the carburetor bowl. Drain as much gas out as possible. Also drain and clean the fuel strainer and clean it with carburetor cleaner. Now either spray or pour carburetor cleaner into the fuel line and let it drain through the carburetor. At first it may not drain, but as it removes the varnish and gunk it should soon begin to flow. For really stubborn and a through cleaning of the carburetor you can replace the plug and fill the fuel line with cleaner and let it sit. I've done this in chainsaws, boats, bikes and cars over the years and have always fixed the problem.
What is the plural form of skidoo?
Th eplural form of skidoo is skidoos
How do you remove water from an outboard motor carburetor?
If you're lucky, there should be a drain plug for the float bowl (the bottom portion of the carburetor). Put a rag or something under the drain plug and then remove the drain plug, letting the gas/water flow out onto the rag. While you're at it, you may want to flush the carburetor with CRC Carburetor Cleaner, or something comparable. Give the cleaner time to evaporate, then put the drain plug back in. (Note: older outboards can have high speed needles where the drain plug should be. You can remove the needle, just make sure when you put it back in, it is in EXACTLY the same configuration it was in before. Also, DO NOT screw the needle in all the way to where it "bottoms out," as this may damage the needle permanently.) Water in the carburetor is NEVER good, and MAY require you to rebuild your carburetor to make sure that any corrosion/gunk has been thoroughly flushed out.
What does the hose attached on the bottom of a 2003 Honda foreman carburetor attach to?
The hose attached to the bottom of a 2003 Honda Foreman carburetor is typically a drain hose or overflow tube. It allows excess fuel or overflow from the carburetor to drain out, preventing fuel from pooling and potentially causing leaks or flooding. This hose usually leads downwards to the ground and is essential for maintaining proper function and safety of the carburetor.
