answersLogoWhite

0

1. Take the tension out of the cable by loosening the adjustment on the cable. 1/2" and 9/16" wrench required.

2. Take the Allen screws out of the right side transmission cover. (may have to remove exhaust to do so.

3. Remove C-clip holding clutch mechanism inside the trans cover.

4. Remove cable from clutch mechanism and unscrew cable from trans cover.

5. Remove pin on handlebar lever and remove cable from lever.

To install reverse removal instructions

***Note*** Be careful when threading new cable into trans case. DO NOT over tighten you will break the new cable

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How do you replace the starter clutch on a 2010 harley-Davidson street glide?

To replace the starter clutch on a 2010 Harley-Davidson Street Glide, first, remove the primary cover by draining the primary fluid and disconnecting the necessary components. Then, remove the clutch assembly and the starter gear to access the starter clutch. Replace the faulty starter clutch with a new one, ensuring proper alignment, and reassemble the components in reverse order. Finally, refill the primary fluid and check for proper operation.


How do you adjust the clutch on a 2004 wide glide harley Davidson motorcycle?

To adjust the cable just go 1/2 way down the clutch cable and pull the rubber over the adjuster. loosten the lock nut and adjust the cable so there is about 1/8" free play at the handle.


How do you remove the clutch on a 1997 dyna wide glide?

how to remove a clutch out of a transmition on a 1997 dyna wide glyde


What is the length of a 1998 harley Davidson flhtc clutch cable?

The length of the clutch cable for a 1998 Harley-Davidson FLHTC (Electra Glide Classic) is typically around 68 inches. However, it's always best to consult the motorcycle's service manual or a parts dealer for the most accurate specifications, as variations may exist based on specific models or aftermarket modifications.


How do you remove stator on 1994 dyna wide glide harley Davidson?

To do this, you must have the manual.


When was the Harley Street Glide made?

The Harley Street GLide, FLHX/I was first introduced in 2006. In 2005 the Harley Road Glide Standard, FLHT/FLHTI was similar to the Street Glide.Hope this helps!Dave


What does the Harley Davidson FLA stand for?

No such model as an FLA. The FL is the Harley Hydra-Glide that eventually became the Duo-Glide.


What is the tire size for a 2000 Harley Davidson Electra Glide?

tire size rear on a 2000 Harley Electra Glide


How much does a Harley road glide weight?

A 2012 Harley Road Glide Custom weighs 817 pounds with all fluids.


How do you adjust the clutch on a 1996 Harley Wide Glide?

Remove the Clutch inspection cover from the primary cover (also called the derby cover). Loosen the clutch cable. The cable adjuster is located about half way down the clutch cable. Adjust so you have a lot of free play in the clutch lever. Go to the the clutch at the primary. You will see an Allen screw in the center of the clutch assembly, with a lock nut. Loosen the locknut several turns and turn in the Allen screw until resistance is felt. (just until you feel it start to tighten.) Then back off the Allen screw 1/2 to 1 turn counter clockwise. Tighten the lock nut to 72 to 120 in lbs of torque. Squeeze the clutch lever several times. Now go back to the clutch cable adjuster. Adjust it so you have about 1/8 inch of play between the clutch lever and the housing, when you squeeze the lever just enough to take up slack in the cable. Tighten the jam nut on the Cable adjuster and reinstall the Primary Cover. You should replace the cover gasket at this time. the torque for the cover is 84-108 inch lbs of torque.


Where is the Harley Davidson Dyna Glide available?

One can find where the Harley Davidson Dyna Glide is available by going the the Harley Davidson website. The website has a number of locations listed where it is sold.


Oil plug location electra glide?

The Harley-Davidson Electra Glide motorcycle oil plug is located on the bottom of the oil pan. You can remove the oil plug with a half inch ratchet.