0
It's not that hard to do....Remove the seat and disconnect the neg side of the battery. Put a towel down where the seat used to be. Then on the console, remove the ugly screw and washer and the little nut below the speedometer.
Once those are off, the whole console will lift up and lay it backwards on the towel. Now you will see the backside of the ignition switch. Unplug the 3 prong connector, and remove the 4 screws that hold the switch in.
There you go......replace and reverse the order to put it back. I cleaned mine up in there after 11 years of road grime build up.
What else can I help you with?
How do you replace an ignition switch on a 2001 Buick Regal GS?
http://www.automotivehelper.com/topic1054152.htm or Goole "ignition switch replacement 2001 regal"
How do you replace an ignition switch on a 2001 Oldsmobile silhouette?
To replace the ignition switch on a 2001 Oldsmobile Silhouette, start by disconnecting the battery to ensure safety. Remove the steering column cover by unscrewing any screws, then disconnect the wiring harness from the old ignition switch. Unscrew the ignition switch from its mounting, replace it with the new switch, and reassemble the steering column cover. Finally, reconnect the battery and test the new ignition switch.
How do you replace an ignition switch on a 2001 Monte Carlo ss 3.8?
Begin by removing the retaining ring at the top of your 2001 Chevrolet Monte Carlo ignition switch. The ignition switch barrel will slide out. Remove the wiring harness from the end of the ignition switch. Reverse the process to install your new ignition switch.
How do you replace an ignition switch on a MB C240 2001?
To replace the ignition switch on a 2001 MB C240, first disconnect the battery to ensure safety. Remove the steering column covers by unscrewing the necessary screws, then locate the ignition switch, which is typically mounted near the ignition lock cylinder. Disconnect the wiring harness and unscrew the ignition switch from its mount. Replace it with the new switch, reattach the wiring, and reassemble the steering column covers before reconnecting the battery.
How much does it cost to replace the ignition switch in a 2001 Suburban?
$109.99 item#IG23401 at schucks.com
Why would ac blower motor and power windows only work when ignition switch is partially engaged on 2001 dodge ram 2500?
The ignition switch is bad. Replace it.
How do you replace an ignition switch in Nissan Frontier 2001?
To replace the ignition switch in a 2001 Nissan Frontier, start by disconnecting the negative battery terminal to ensure safety. Remove the steering column covers by unscrewing the screws and gently prying them apart. Next, locate the ignition switch, detach the wiring harness, and unbolt the switch from its position. Install the new ignition switch by reversing the steps, reconnect the wiring, and reassemble the steering column covers before reconnecting the battery.
How do you replace a 2001 Toyota Tundra ignition switch?
To replace the ignition switch on a 2001 Toyota Tundra, first disconnect the battery to ensure safety. Remove the steering column covers by unscrewing the screws and gently prying them apart. Next, locate the ignition switch behind the ignition lock cylinder, detach the wiring harness, and remove the mounting screws to take out the old switch. Finally, install the new ignition switch by reversing the process, reconnect the wiring, and reattach the steering column covers.
How do you remove iginition switch Mazda tribute 2001?
To remove the ignition switch from a 2001 Mazda Tribute, first disconnect the negative battery cable to ensure safety. Then, remove the steering column cover by unscrewing the screws that hold it in place. After that, locate the ignition switch, disconnect the wiring harness, and unscrew the ignition switch from its mounting. Finally, carefully pull the ignition switch out and replace it with the new one if needed.
How do you change a ignition switch on a 2001 Chevrolet Camaro?
The 2001 Chevrolet Camaro ignition switch is held in place with a retaining ring. Remove the retaining the ring and slide the ignition switch out. Remove the wiring harness. Reverse the process to install the new ignition switch.
How do you change ignition coil in Nissan sentra 2001?
How change my ignition switch nissan 2001 sentra.
How do you replace hazard switch 2001 Oldsmobile alero?
How do you replace the hazard switch
