answersLogoWhite

0

As far as I know, there is no noteworthy difference in the way most bikes stop either by using the kill switch or the key. The engine's ignition gets cut either way and as far as the engine is concerned that's the end of it. On practical grounds, however, there is something to be said for using the key: it's a good habit to acquire, for using the kill switch might lead to forgetting the key in/on, straight to a lost/stolen key/bike or possibly a flattened battery. Also, once used, one tends to forget the kill switch on "off", prompting a few moments of confusion when the bike is to be started again...

User Avatar

Wiki User

10y ago

What else can I help you with?

Related Questions

Can you switch back after using synthetic oil in motorcycle back to regular oil?

yes


How is energy used in your lives?

Through switching on a light or turning on a kettle is a way of using our energy because when you switch on something that electricity is using energy to help it to switch on..


How is energy used everyday in your lives?

Through switching on a light or turning on a kettle is a way of using our energy because when you switch on something that electricity is using energy to help it to switch on..


If you take out the fuse for the air suspension compressor in the 1993 Lincoln town car but don't shut it off in the trunk can you damage the system if you have the vehicle towed?

No. Removing the fuse shuts off the power supply the same as turning the switch to the "OFF" position. I would recommend using the switch in the trunk.


How can I adjust the brightness of my lamp using a lamp dimmer cord?

To adjust the brightness of your lamp using a lamp dimmer cord, simply plug the lamp into the dimmer cord and then adjust the brightness using the dial or switch on the cord. Turning the dial or switch clockwise will increase the brightness, while turning it counterclockwise will decrease the brightness.


How can I adjust the brightness of my LED lights using a dimmer switch?

To adjust the brightness of LED lights using a dimmer switch, make sure the dimmer switch is compatible with LED lights. Install the dimmer switch according to the manufacturer's instructions. Then, use the dimmer switch to adjust the brightness by turning the knob or sliding the switch up or down.


How can I properly hook up a generator to my house using a transfer switch?

To properly hook up a generator to your house using a transfer switch, follow these steps: Install a transfer switch near your main electrical panel. Connect the generator to the transfer switch using a power cord. Turn off the main power supply to your house. Start the generator and switch the transfer switch to the generator position. Power will now be supplied to your house from the generator. When utility power is restored, switch the transfer switch back to the utility position and turn off the generator.


How can I operate a gas fireplace with a wall switch?

To operate a gas fireplace with a wall switch, first ensure the gas supply is on. Then, simply flip the wall switch to the "on" position to ignite the fireplace. Adjust the flame height and temperature as needed using the switch. Remember to turn the switch to the "off" position when not in use for safety.


How can you start and stop electric circuit?

You can start an electric circuit by closing the circuit, typically by turning a switch on. You can stop an electric circuit by opening the circuit, usually by turning a switch off or disconnecting a wire.


How do you turn on a gas fireplace using a wall switch?

To turn on a gas fireplace using a wall switch, first locate the switch on the wall near the fireplace. Flip the switch to the "on" position. Then, press and hold the ignition button on the fireplace until the pilot light ignites. Finally, release the button and adjust the flame height as needed using the wall switch.


How can I properly connect a generator to my house using a transfer switch?

To properly connect a generator to your house using a transfer switch, follow these steps: Install a transfer switch near your main electrical panel. Connect the generator to the transfer switch using a power cord. Turn off the main power supply to your house. Start the generator and switch the transfer switch to the generator position. Power will now be supplied to your house from the generator. When the main power is restored, switch the transfer switch back to the main power position. Remember to always follow safety guidelines and consult a professional if needed.


What are the key steps involved in manual transfer switch installation?

The key steps involved in manual transfer switch installation include: Choosing a suitable location for the switch near the electrical panel. Turning off the main power supply to the panel. Mounting the transfer switch on the wall. Connecting the switch to the electrical panel using appropriate wiring. Testing the switch to ensure it functions properly. Turning on the main power supply and testing the switch again for proper operation.