0
BY applying a voltage to the relay's coil connections. Could be DC or AC at a specific voltage. If it's DC, watch the polarity. If it's AC, polarity doesn't matter. HOWEVER, VOLTAGE DOES MATTER, so don't go applying 120 VAC to a relay when it needs only 16 VAC, and DON"T APPLY AC to a DC relay. Could burn up quite nicely if you're not careful.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
What is Blast Furnace?
A blast furnace is used to extract iron from its ore.
How much voltage is required to energize the 8051 microcontroller?
The 8051 runs on +5vdc.
How can you include phase failure relay in your star delta motor starter circuit?
The star delta motor starter circuit has to have a control voltage to energize the motor magnetic contractors. A phase failure relay monitors all three phases of the incoming supply lines. The phase failure relay also has auxiliary contacts on it. There are usually two sets of "C" form contacts. The control voltage for the starter circuit must be connected across the normally open (N.O.) contacts of one of these two sets. When the phase monitor is energized these N.O. contacts close supplying the control voltage to the circuitry of the star delta starters. If there is a phase interruption, phase reversal or phase loss, the phase failure relay will de-energize and the N.O. contacts will go back to their de-energized state. If the star delta motor starter is in use at the time, its control circuitry voltage will be lost and the delta motor magnetic contactor will open. The opening of this contactor will disconnect the motor from the failed three phase supply.
How much money did Out of the Furnace gross domestically?
Out of the Furnace grossed $11,330,849 in the domestic market.
How much electricity was required to energize the flux capacitor IN Back to the Future?
1.21 Gigawatts
What happens if you energize power to wire on n.c. contacts?
If the relay contacts are in series with a connected load, then the load will energize.
What the Generator lockout relay?
generator lockout relay is a relay that the output of other relays energize this relay and its out put use for tripping of generator. this relay must be reset manually
What is cut out relay?
The cut out relay is used to energize a fuel pump. It then shuts down, until it gets impulses from the spark plugs.
How do you wire the horn button?
Most horn buttons provide the ground to energize the horn relay. The horn relay when triggered sends power to the horn.
How do you identify an electric furnace from a gas furnace?
an electric furnace runs off of 208/230 Volts while a typical gas furnace runs off of 120 also a gas furnace will have a valve for the gas relay where the gas enters the furnace.
A fan or cooler relay is used in electric furnace to change the blower speed to the speed for cooling?
A fan or cooler relay is used in electrical furnace to change the blower speed to the blank speed for cooling
How do you check the under voltage relay?
The way you check to see if an under voltage relay is wired properly is to disconnect the electrical supply. If the device that is connected to the load side of the relay does not start up or energize when the electrical supply is reconnected, then the relay is connected correctly.
Need to know how to reconnect RBM type 184 fan relay to Coleman furnace old relay disconnected without diagram made for wiring need to know what colors go to which post on relay?
Need to know how to reconnect RBM type 184 fan relay to coleman furnace old relay disconnected without diagram made for wiring need to know what colors go to which post on relay?
A fanor cooler relay is used in an electric furnace to change the blower speed to the?
low
When you turn off your 1989 Camaro RS your fuel pump keeps running and kills your battery. What is the cause and the fix?
The '89 Camero RS has an electric fuel pump and a relay to operate it. The relay is "turned on" by the ignition system. When the key is turned to "start" or "run" the relay is energized. (The relay is used so it can be operated from the switch. The pump itself draws too much current for it to be practical to run the pump directly through the ignition switch.) Normally the relay will energize and close and then de-energize and open with the operation of the key (ignition switch). That starts and stops the fuel pump. But if the relay is stuck "on" (the contacts remain closed) then the switch will de-energize it but it will keep the fuel pump powered up. The relay may be mechanically stuck or the contacts may have gotten "welded shut" during operation. Either way, the relay is the primary suspect in this case. Good luck with your troubleshooting and repairs.
Are potential relays used to energize or de energize split phase motors?
Yes, potential relays are used to energize and de energize split phase motors.
What powers your 2000 fucus engine fans?
Usually there is a fan relay that is controlled by the engine computer. The relay coil is usually fed 12 volts and the return (ground) wire is grounded by the computer to energize the relay. The relay is there to handle the high amperage current that runs the cooling fans. Problems in this area can be caused by the relay being bad or the power source for the fans being absent.
