To set the clock or calendar:
press and hold the set button for 3 sec's
then toggle through the functions using the set button
use the "+" & "-" buttons on the back to adjust the feature
to set the alarm:
hold clear button for 3 sec's
to select either the 1st alarm (A1) or the 2nd (A2) use + & - buttons
press clear button to confirm
to set alarm time + & - to enter hr &b min values them clear button to confirm
to view alarm time press clear button
to switch between A1 & A2 use + & - buttons
hope this helps
If that doesn't work try this:
I stumbled on it. Remove AC to DC power and batteries in home station. Then put batteries back in and connect AC. Remote Temperature should appear if you have the correct channel.
You are in luck. I had to replace the batteries in my DWS-150 & couldn't find the instruction manual to reset the time. Fortunately, I remembered a while back I had the same situation & thought I might have downloaded the manual - while it was still available. Ifound I have it saved as a pdf file on my pc. Here are some excerpts: About the Atomic Clock The National Institute of Standard and Technology (NIST) in Fort Collins,
Colorado broadcasts the time signal (WWVB at 60kHz AM radio signal) with
an accuracy of 1 second per every 3,000 years. The signal will cover a
distance up to 2,000 miles from the source. Like a typical AM radio, your
Atomic Clock will not able to receive the WWVB signal in places
surrounded by heavy concrete or metal panels. The reception of the time
signal can be affected by mobile phones, TV, electrical appliances or other
electronic interference. To get the best performance of the Atomic clock,
please install the home receiver near a window and away from large metallic
objects. If the unit is not working properly, change the unit position. There
may be some interference at this location.
7
DWS-150-IB SP\ENG 10/12/04 11:30 AM Page 7
SETTING TIME
RADIO-CONTROLLED CLOCK
The home receiver will start synchronizing the clock after the 1st channel of
the RF thermometer is registered.
1. At normal mode, hold the " - " button located on the back of the home
receiver for 3 seconds to force synchronization.
2. The antenna icon will appear during the synchronization process (on the
right side of the time display).
3. If the icon disappears afterwards, radio time signal is not available at that
moment. Try setting the home receiver in other locations. Remember to
place the unit away from sources of interference such as mobile phones,
appliances, TV etc.
4. Antenna icon will appear on screen if the radio time reception is
successful. The radio-controlled clock will have a daily synchronization at 1:00 am everyday. If previous attempts of reception were
unsuccessful, the home receiver will attempt synchronization
each hour until successful.
5. Each reception cycle is minimum 2 minutes and maximum 10 minutes.
TIME ZONE SELECTION
Press " - " button on back of home receiver to select from the following time
zones in the U.S. (zone is displayed in the upper right hand corner of time
display).
P - Pacific Standard Time M - Mountain Standard Time
C - Central Standard Time E - Eastern Standard Time
MANUAL SETTING FOR CLOCK & CALENDAR
1. Hold "SET " button for 3 seconds to enter clock set.
2. First, select 12 hour or 24 hour setting using the " +, - " buttons located
on the back of the home receiver. Press " SET " button to confirm.
3. Select Hour - Use the " + , - " buttons located on the back of the home
receiver to adjust hour setting. Press " SET " button to confirm.
4. Select Minute - Use the " + , - " buttons located on the back of the
home receiver to adjust minute setting. Press " SET " button to confirm.
5. DST On/Off (Daylight Savings Time) - Use the " + , - " buttons to turn
DST on or off. Press " SET " button to confirm.
Now you will select the calendar settings-
6. Select Year - Use the " + , - " buttons located on the back of the home
receiver to adjust year setting. Press " SET " button to confirm.
7. Select Month - Use the " + , - " buttons located on the back of the
home receiver to adjust month setting. Press " SET " button to confirm.
8. Select Day - Use the " + , - " buttons located on the back of the home
receiver to adjust day setting. Press " SET " button to confirm.
9. Select Fahrenheit/Centigrade Temperature Readings - Use the
" + , - " buttons located on the back of the home receiver to toggle
between Fahrenheit or Centigrade readings. Press " SET " button
to confirm.
2
The noun 'set' is a standard collective noun for:a set of bowlsa set of cutlerya set of dishesa set of golf clubsa set of knivesa set of mathematiciansa set of oystersa set of sailsa set of tires
* Set It Off * The TV Set * Murder-Set-Pieces
Range is the biggest number in a set of data subtracted by the smallest number in that set of data.
It is set in 1900.
Act 1 is set in the Piazzetta, Venice Act 2 is set in the pavilion in the Palace of Barataria.
Your Envirastation DWS-2220 will set itself. It is recommended that you install the home receiver near a window and away from metallic objects.
My Manual for 220 gives Contact 1 800 466 3342 Contact Envirastation Customer Relations Service dept 168 3000 Pontiac Trail Commerce Township, Mi 48390 cservice@envirastation,com
envirastation dws-210 instructions
wireless weather station
I think I solved the problem of programing the EnviraStation DWS-200. To keep the settings from reverting to the setting you are trying to change, press the 'set' button one more time after you have gone through all the settings.ie, you start by pressing 'set' and holding it down for 3 seconds.that brings up the 12/24 hour choice, press set again to get to the hour.Adjust the hour with the + & - buttons on the back, then press set to advance to minutes.continue through to the year month and day settings and when all is done,PRESS SET ONE MORE TIME.Anyway after a couple of hours looking for information and always having it revert to thetime I was trying to change, I finally found some instructions for the DWS-220, which is set from an atomic clock, but there were instructions for manual setting, it was there that I saw the information about that last push on the set button. It's worth a try.
I had the same question, but answered it myself. You push, and hold the center of the three buttons on the back of the main (not remote) unit, until you hear a "beep." This will cause an icon on the front to begin flashing. Sit the remote unit right next to the main unit, and wait a couple of minutes. Eventually, the unit will automatically program and you're ready to go.
Go to Google and type in EnviraStation DWS220 you'll find a link on answers.com and you can download a pdf manual. I found it today, 11-5-08.
Go to Google and type in EnviraStation DWS220 you'll find a link on answers.com and you can download a pdf manual. I found it today, 11-5-08.
To set the clock or calendar: press and hold the set button for 3 sec's then toggle through the functions using the set button use the "+" & "-" buttons on the back to adjust the feature to set the alarm: hold clear button for 3 sec's to select either the 1st alarm (A1) or the 2nd (A2) use + & - buttons press clear button to confirm to set alarm time + & - to enter hr &b min values them clear button to confirm to view alarm time press clear button to switch between A1 & A2 use + & - buttons hope this helps If that doesn't work try this: I stumbled on it. Remove AC to DC power and batteries in home station. Then put batteries back in and connect AC. Remote Temperature should appear if you have the correct channel.
Google has this cached, although I'm not sure whether this link is permanent. It contains both English and Spanish. http://72.14.205.104/search?q=cache:_AfEpOb9h48J:www.homedics.com/prod/getpdf.aspx%3Fname%3DDWS-150-IB.pdf+envirastation+dws-150&hl=en&ct=clnk&cd=5&gl=ca
Google has this cached, although I'm not sure whether this link is permanent. It contains both English and Spanish. http://72.14.205.104/search?q=cache:_AfEpOb9h48J:www.homedics.com/prod/getpdf.aspx%3Fname%3DDWS-150-IB.pdf+envirastation+dws-150&hl=en&ct=clnk&cd=5&gl=ca
the set of every set is that set