The easiest way is to put a high resistance in series with the meter.
You must know the input resistance of the meter. This is specified in the owner manual.
Some meters are specified as having a certain input resistance.
If a meter has a 1 Megohm input resistance, you can scale it up by a factor of ten by putting a 9 Megohm resistor in series with one of the probes.
Some meters are specified in "ohms per volt".
The Ohms/V rating can be different on different scales. If a meter is specified on the 600 volt scale as having "20,000 Ohms per Volt", then this means that the meter's resistance is 20,000 * 600, = 12,000,000 Ohms. 12 Megohms.
To expand the meter's 600V scale to 10X the rating (6,000 volts), you would put a 108 megohm resistance in series with the probe. This resistance could be made up of ten 10 Megohm resistors, a 7.5 megohm resistor, and a 470 Ohm resistor. Even though that is only 107.97 megohms, the error is less than 1%.
To expand the scale to 2X (1,200V) you would put a 12 megohm resistance in series with the probe.
High voltage low power resistor strings can be put inside plastic, glass, or ceramic pipes. Consult the appropriate industry publications for recommendations.
warning:
Be careful when measuring high voltages. Never work alone.
Most simple resistors are not rated for high voltage over 200-500 volts per each resistor and will arc or burn. Injury or death may result.
I prefer to hook the "hot" end of the probe to the high voltage test point and let it hang there, and not to hold it by hand. Then I energize the equipment and take the readings. After I am done, I discharge the high voltage and safely remove the probe from the equipment.
Poorly made or defective probes have killed people.
If the voltage measured exceeds the voltmeter range then the voltmeter needle remains in it's maximum position until it's voltage values are considerably reduced.
A voltmeter measures voltage in volts.
A galvanometer can be converted into a voltmeter by connecting it with very high resistance.
A: It is a regular DC voltmeter but the AC is rectified and the DC component is measured and displayed as AC VOLTS.
generally voltmeters are connected in parallel in the circuit.If the voltmeter resistance is lower as it increases the current rating,because by connecting parallel we are decreasing the resistance,so if the voltmeter resistance is not too much higher it leads to burning of the meter,For that we can conclude that the in ideal the voltmeter has infinite resistance.
why is extention
The formula for calculating the least count of a voltmeter is least count = Range / Number of divisions. Where the Range is the maximum voltage that the voltmeter can measure and the Number of divisions is the total number of divisions on the voltmeter scale.
If the voltage measured exceeds the voltmeter range then the voltmeter needle remains in it's maximum position until it's voltage values are considerably reduced.
With the pointer mid range on the scale, the reading of the multi-range voltmeter would be 125 volts.With the pointer mid range on the scale, the reading of the multi-range voltmeter is 125 volts.
Voltmeter connect in parallel with the circuit setting on voltmeter highest range first then to lower range. Ohmmeter we need to use the ohmmeter meter setting connect across the resistor
2 volts
Multi-range ammeter using universal shunt
If the voltage is completely unknown, a voltmeter should be set to the maximum range first, then stepped down to an accurate level.
if we would like to expand the range of voltmeter we should change the voltmeter resistance even to be appropriate . we should use a variable resistance to control of its value . I would extend the range of a voltmeter by adding resistance in series with it. I would extend the range of an ammeter by connecting resistance in paerallel with it.
The price of a voltmeter can vary depending on the brand, model, and features. On average, a basic analog voltmeter can range from $10 to $50, while a digital multimeter with more advanced capabilities can range from $20 to $200 or more.
To measure electrical voltage accurately using a voltmeter, first ensure the voltmeter is set to the appropriate voltage range. Connect the voltmeter in parallel to the circuit or component you want to measure. Take note of the polarity and read the voltage displayed on the voltmeter. Make sure to account for any decimal points or units displayed.
To measure voltage in a circuit, the voltmeter should be connected in parallel across the component or portion of the circuit where the voltage is to be measured. Ensure the voltmeter is set to the appropriate voltage range before making the connection. It is important to place the voltmeter correctly to obtain an accurate voltage reading without affecting the circuit's operation.