Peak power is the highest rated output of the speaker when loud (or peak) parts hit. Continuous/nominal power is the average output at normal and continuous listening levels. If you have the Peak Power rating, you can figure out the nominal level by multiplying the peak power by the square root of two (0.707).
Peak Power * 0.707 = Nominal Power.
Most power amplifiers will handle a load of 6 ohms. The spec you need to look at is the power handling of the speakers. If they are rated for 100 watts program power, then look for an amplifier rated for 100 watts RMS output. Any amplifier can be connected with adapter cables to the typical 1/8" output of your computer.
well, your lookin at RMS when it comes to speakers and amps, if you bought a 800 watt amp, you would be looking at 400 RMS just as you do with your speakers, i would recommend a 1600 watt amp, just for the fact that you always want a little play room with your amp, this way you wont blow the amp, (amps are more expensive than speakers), and if you decide that you want to get bigger speakers, you will not have to replace the amp. But all in all, i would say anywhere from 1200 to 1600 would do just fine for your sub..-Shocker
The speakers will work with any amp that outputs less power than 700 watts.
a channel refers to the speakers or subs. for example a 2 channel amp can power 2 subs or speakers. a 4 channel will power 4.
It means 1000watts in DC power. AC its a little more tricky.
It depends on the power handling capability of the speakers. Generally, a 500-600 watt amplifier would be sufficient to power two 15-inch speakers that have a power handling capacity of around 250-300 watts each. Make sure to match the amplifier's power output with the speakers' power handling to avoid damaging the speakers.
The JBL MR902 speakers are designed to handle up to 180 watts of power. This means that they can handle up to 90 watts RMS (continuous power) per speaker. It is important to match the speaker's power handling with the appropriate amplifier power to avoid damaging the speakers.
Around 150Watts. continuous/nominal power is found by multiplying the peak power by the square root of two (0.707). in this case peak power = 400, therefore 400 * 0.707 ≈ 280 watts
Bass Blocker will not raise the power a speaker can handle. It will keep low frequencies from distorting and damaging smaller speakers that cannot handle low bass.
Yes.
Freq response: (+/- 3dB): 60Hz - 21KHz Impedance: 6 ohms nominal Power Handling: 50 watts RMS, 150 watts peak Sensitivity: 89 dB Crossover freq: 4500 Hz Woofer: 6.5 ", Tweeter: .75" Mylar dome
Most power amplifiers will handle a load of 6 ohms. The spec you need to look at is the power handling of the speakers. If they are rated for 100 watts program power, then look for an amplifier rated for 100 watts RMS output. Any amplifier can be connected with adapter cables to the typical 1/8" output of your computer.
Yes it can. The rated power of the speakers is the MAXIMUM that can be applied. If more power is supplied, damage can occur. Either the speech coil can blow or mechanical damage to the cone or suspension units.As the amplifier is below this rating, it will not supply more power than the speakers can handle and will be perfectly safe.
The power of speakers is typically measured in watts, which indicates how much electrical power the speaker can handle without distortion. This measurement can be found in the speaker's specifications as "RMS" (Root Mean Square), which reflects the continuous power the speaker can manage, and "peak" power, which indicates the maximum power level for brief moments. Additionally, sensitivity ratings, expressed in decibels (dB), measure how effectively a speaker converts power into sound, providing insight into its loudness at a given power input.
No. Two 16 ohm speakers connected together are either 32 ohms, if wired in series, or 8 ohms, if wired in parallel. You can, however, connect four 16 ohm speakers in series-parallel to get 16 ohms, with four times the power handling capacity of just one.
You can power two 400W speakers if you have Peavey PV115 using a 2000W power.
No, the speaker watts should not be more than the amplifier output in terms of power. It is important to match the speaker's power handling capability with the amplifier's output power to avoid damaging the speakers. It's recommended to have an amplifier that can deliver power within the range recommended for the speaker.