0
60898 is an IEC standard; there are two parts. 1 is for AC, 2 is for DC.
IEC 60898-1 "applies to a.c. air-break circuit-breakers for operation at 50 Hz or 60 Hz, having a rated voltage not exceeding 440 V (between phases), a rated current not exceeding 125 A and a rated short-circuit capacity not exceeding 25000 A."
IEC 60898-2 "gives additional requirements for single- and two-pole circuit-breakers suitable for operation with direct current, having a rated d.c. voltage not exceeding 220 V for single-pole and 440 V for two-pole circuit-breakers, a rated current not exceeding 125 A and a rated d.c. short-circuit capacity not exceeding 10000 A. This Part 2 is to be used in conjunction with IEC 60898-1." (quotes taken from IEC abstracts)
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What are the patches on the jacket that mickey rourke wore in the movie harley Davidson and the marlboro man?
1.Aces and 8's (Dead man's hand with skull). 2.SRV (Tribute to S.R. Vaughn with birth and death dates in Roman numerals) 3.Cross (With Gaelic slogan "Tiocfaidh á Lá!" 'Our time will come') 4.Harley Davidson (Mickey's character in movie) 5.BartelsHD (Shop where original BD3's were made) 6.Schwarzer Tod (Black Death in German) 7.MCB FXRS (MotorCycle Boy, Black Death 3 before it was built up) 8.Wyoming Outlaw (Please note the correct blue on orange color - not white on orange) 9.Evolution (Engine in BD3) 10.Bonne Nuit Salope (Goood Night Whore) 11.Sturgis 50 1990 12.'Z' Custom Leathers for the back you can get this jacket with the all patches, an exact replica on celebswear.com
Interview questions for electrical maintenance?
1. Describe the electrical systems you have worked on and how did you get your training? 2. What is your experience with electrical schematics? 3. What is your experience with ladder logic? 4. Describe the malfunctions you have experienced with PLC hardware? 5. Describe a tough electrical troubleshooting problem you have experienced, and briefly explain the steps you used to solve the problem. 6. What is the difference between a digital signal and an analog signal? 7. How often do you use a personal computer in a typical day? What do you do with it? 8. Describe a process problem you have experienced and how did you solve it? 9. Give an example of a tough loop you had to tune. What were the problems? And how did you solve them? 10. What brands of VFD's are you familiar with. 11. Describe some of the malfunctions associated with VFD's, and give an example of a tough VFD problem you had to solve. 12a. Using Ladder logic, write a program that will START and STOP a motor with momentary START and STOP push buttons. (Provide a sheet of paper) 12b. Add ladder logic that will turn the motor OFF after running for two minutes. 13. Describe the steps you take to troubleshoot a 3 phase, 480 volt motor that continually trips the heaters. 14a. Why is the earth pin in a 3-pin plug the longest and the thickest? 14b. Explain the purpose of grounding. 15. Describe a control panel you wired, designed, or modified. What was the purpose of the panel and state each component you used. 16. Describe the difference between a sourcing input and a sinking input. 17. Why do you want this job? PWR 1)sensitivity of ELCB PWR 2)about MCB ratings PWR 3)earth resistance and earth compounds PWR 4)what is LDR PWR 5)your electrical activity in your society PWR 5)CONSTRUCTION OF CAPACITOR PWR 6)transformer and related formulas PWR 7)industrial lightings PWR 8)what is the nature of electrons PWR 9)use of ballast in tube light PWR 10)CABLE SIZE AND AMPERE RATINGS
What is the 'short circuit capacity' of a 32A 60898 MCB?
Depends on manufacturer..Normally the ratings are as follows 1. Service short circuit breaking capacity is 7.5 kA 2. Rated short circuit breaking capacity is 10 kA.
What meaning mcb?
MCB, Miniature Circuit Breaker is electric switch which is used to protect against short circuits
What is the full form of MCB?
The definition of MCB is a miniature circuit breaker, it trips if there is a line to natural fault. Ill add some extra information about the different types. RCD - residual current device = This is what you could separate you're circuits up with by inserting 1 of these in you're consumer unit (if you have lets say 10 circuits it goes like this... rcd-mcb-mcb-mcb-mcb-mcb-rcd-mcb-mcb-mcb-mcb-mcb-main switch. you see the rcd's control 5 circuits each, if 1 of these circuits had an earth fault on it, the rcd will trip and 5 of them circuits will go off, which means you have to keep tripping in you're rcd with an mcb 1 at a time to see which circuit the fault is on. RCBO - residual current breaker with overload protection- These can be installed in place of mcb's and rcd's, the rcbo is an mcb and rcd in 1 breaker. For example, i have installed a consumer unit full of these, in this case if a circuit forms a fault then its only that circuit that goes off. I hope this extra piece of information helps you along and best of luck. <<>> In electrical terminology MCB stands for Miniature Circuit Breaker.
What is a mcb and what is it used for?
mcb is master circuit breaker. it is used in the circuit for the protection of equipments from over voltage.
What is mcb and cb?
MCB = Miniature Circit Breaker CB = Circuit Breaker
What is meant by mcb and dp?
MCB = Miniature Circuit Breaker DP = Double Pole
How do you select an MCB?
While selecting an MCB you have to check: 1) Current Rating; 2) Response Time; 3) Manufacturer; 4) Type of MCB (means single pole, double pole, three pole, four pole - it depends on the application); 5) Cost; 6) short circuit breaking capacity. For more information see the answers to the Related Questions and the Related Link shown below.
What is the surge current limit for a 40 A MCB?
A 40A MCB is a circuit breaker. The surge current limit is protected to 250A 8/s0uS. The limitation capability of a circuit breaker is that characteristic whereby a current less then the prospective fault current is allowed to flow under short circuit conditions.
Why 28 days test required for mcb testing why not 30 days?
The standard for testing of Miniature Circuit Breakers - IEC 60898 has arbitrarily decided on 28 days during which the temperature rise is to be measured. The standard states: "The circuit-breaker is in the closed position, the current being established and interrupted by an auxiliary switch. During this test the circuit-breaker shall not trip. During the last period of current flow the temperature-rise of the terminals shall be measured." If the characteristic can be verified for 28 days, the MCB passes the test. Hence 28 days, and not 30 days.
What is difference between spn and tpn mcb db?
TPN MCB means Triple pole Neutral Miniature Circuit Breaker where as SPN MCB means single phase Neutral MCB.
What is the full form of MCB's in Physics?
It is miniature circuit breaker
What are the difference MCB and CB?
The main difference between MCB, RCCB, and Isolators Isolators are generally used in power system while on the other hand, MCB is the circuit breaker. Isolators are manually-operated device, and on the contrary, the circuit breaker is the automatically-operated device.
