answersLogoWhite

0

it convert ac signal into dc signal

But it will give only half-wave rectification.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

A single-phase transformer when supplied from 220v50hz has eddy current loss of 50wif the transformer is connected to a voltage of 330v50hzthe eddy current loss will be?

112.5


What is this system called with three single phase transformer?

Your question is rather vague. If you are asking what do you call a group of single-phase transformers, connected to supply three phase, then the answer is a 'three-phase transformer bank'.


How to Construct a single to threephase inverter?

Very complicated, first you have to rectify your single phase to get DC then you need a 3 phase sine wave signal, that can be generated with a MCU, to drive three pairs of push pull amplifiers that is connected to a three phase transformer's primary windings and you have your output at the secondary


What is a single phase variac?

It is a variable autotransformer, a transformer with a sliding contact on the winding connected to a control knob, that allows the output voltage to be varied.


What happen when 220v dc is applied to a 220v ac single phase transformer?

The current would rise until it blows the fuse or breaker and that would produce an arc as the transformer's inductance tries to maintain the current.


Why do you use Two Winding run and start winding in the single phase motor?

Any transformer uses a minimum of two windings to change the voltage value. The primary side of the transformer is usually connected to the existing voltage. The secondary side of the transformer is usually connected to the load, who's voltage could be higher or lower voltage than the primary voltage.If the secondary voltage is increased the transformer is known as a step up transformer and if the secondary voltage is decreased the transformer is known as a step down transformer.The transformer terminal markings for the primary are H1 and H2 on a single coil primary and H1 to H4 on a dual voltage primary winding. Like wise the secondary terminal markings are X1 and X2 on a single coil secondary and X1 to X4 on a dual voltage secondary winding.


On a stup down transformer what does the xo symbol mean?

On a step down transformer XO symbol denotes the secondary split phase grounding point. This is also where the neutral of the three wire secondary is connected. The transformer connection is known as a single phase - three wire - with one secondary winding.


What is the biggest size of single phase transformer?

Today the highest voltages are 800 kV. These are commercially installed transformers that are used for the transmission of power throughout the grid that they are connected to.


What will happen if the four conditions are not maintained in case of single phase transformer?

Without knowing what you mean by 'the four conditions', it's going to be difficult to answer your question.


How many windings does a single-phase transformer have?

Generally a single-phase transformer will have twowindings. One of the Low voltage side and one on the high voltage side. North-American distribution transformers will have three: one high-voltage winding, and two low-voltage windings connected in series.However......a single-phase transformer can also have several primary and several secondary windings. The primary windings can be connected in series or in parallel with each other, as can the secondary windings. For example, taking the primary winding as an example, it could consist of two 120-V rated windings: if connected in series, it could be supplied with 240 V without exceeding its voltage rating; if connected in parallel, it could be supplied with 120 V without exceeding its voltage rating. Multiwinding single-phase transformers allow for a variety of connections.


What will happen if apply two phase supply to a three phase transformer?

A three phase transformer is simply three transformers so, supplying one phase to a set of three transformers will result in only one phase output. Any loads connected to that transformer that are expecting three phase power will malfunction, and could fail.AnswerA three-phase transformer is NOT 'three separate single-phase transformers', as suggested in the original answer. It is a single transformer with three primary and secondary phase-windings wound around a common three-limb ('core') or five-limb ('shell') core. If a single-phase supply was applied to one of the three primary windings, then single phase voltages would appear across each of the three secondary windings and the remaining two primary windings. These voltages would not be out of phase with each other.


What type of transformer has only a single winding?

the auto transformer is the one winding transformer. it ismaily used in practical purpose.