0
Globes are a representation of the planet Earth.
The axis of spin of the Earth is tilted sideways with respect to the plane in which it orbits the Sun.
Globes of the Earth are therefore constructed to represent this tilt.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
Who was the man who risked his life for brother man?
John Shaft, the lead character of the film Shaft - the line is a lyric from the film's theme song.
How much money did Shaft gross worldwide?
Shaft grossed $107,190,108 worldwide.
What was the Production Budget for Shaft?
The Production Budget for Tower Heist was $85,000,000.
In which 2000 movie did Richard Roundtree play the character Uncle John Shaft?
Shaft Richard Roundtree reprised his role as the original "Shaft" in the 2000 remake, and Samuel L. Jackson played his nephew.
What was the movie Shaft based on?
The 2000 movie Shaft, starring Sam Jackson, was a remake of the 1971 movie of the same name, which starred Richard Roundtree as John Shaft.The original Shaft movie was based on the novel by Ernest Tidyman.
What is reverse shaft?
A Reverse Shaft is the shaft which rotates in the opposite direction of the engine driver shaft with the help of meshing of gears mounted on it to the gears mounted on engine driver shaft when reverse gear is applied. The reverse shaft allows the vehicle to move in reverse direction. Sanjay Singh Rathore (ME 3rd year) M.I.T.Mandsaur
What is a overhung pump?
A centrifugal pump whose impeller is mounted on the end of a shaft that overhangs its bearings.
What is an eccentric shaft?
A shaft is usually longish bit of rotating machinery, made to transfer rotating power. Eccentric means off-center. Either the shaft isn't round, or it's not mounted at the center of wherever it it.
What is tail shaft?
Tail Shaft is the section after the propeller shaft of a shift. Any shaft is always placed farthest from the head, where the power is applied.
What is a Monoblock pumps?
A Monobloc pump is a pump in which all rotating parts are mounted on a common shaft. The main components of a Monobloc pumps are Pump assembly and Motor assembly. Since there are 7% losses in belt driven sets and 3% losses in coupling driven sets hence to avoid these transmission losses Monobloc pump sets evolved. In monobloc pump sets as motor and pump are mounted on a single shaft there is no energy loss during energy transmission from motor to shaft.­­­­­­­­ By - Tanveer Ahmed Bankapur
What is a spindle on a 1995 Chevy corsica?
The spindle is what the front wheel is mounted on. It is the shaft that the wheel bearing slides up on.
What makes a bang stick not a firearm?
The very long shaft that the powerhead is mounted on, which makes it unsuitable for use as a weapon.
What composer won the Golden Globe for Best Original Score - Motion Picture in 1972?
Isaac Hayes won the Golden Globe for Best Original Score - Motion Picture in 1972 for Shaft.
Where is the crank sensor located on a 1998 Chrysler Sebring?
A) On a 2.0L & 2.5L DOHC (1999 & earlier) Engines, The crank shaft sensor is mounted above the oil filter. B) On 2.4L DOHC ( 2001 & later) engines, the crankshaft sensor is mounted on the rear side of the engine block C) On 2.5L V6 engines, the crank shaft is mounted under the distributor near the transaxle housing.
Where is the location of the water pump on a 1991 Ford F-150?
it is on the front of the motor your fan is mounted on the water pump shaft
Where is the throttle body sensor?
Assuming you are asking about the throttle position sensor it is mounted on the throttle body and is operated by the throttle shaft.
Where is the crank shaft sensor for a 94 Chevy Corsica?
On 3.1L Engines it is on the front of the engine above the starter mounted in the engine block. On 2.2L engines it is above the oil filter mounted in the engine block.
