answersLogoWhite

0

The unit should run OK on a modified sine wave since motors are not that sensitive to the waveform. Efficiency might be slightly reduced.
The real problem may be in starting the unit. If the input does not have enough power to allow the compressor to start properly and it stays running on the start winding, it could burn up the start winding. Checking the current input with a clamp-on style amp-meter should show if it is drawing excess current by running on the start winding.

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Movies & Television

Is square wave inverter harmful to electronic devices?

Depends on the device. For instance almost all laptop power supplies use a international (aka universal) switch mode power supply. They don't care about modified sine wave output at all! Almost all low-cost inverters use a step-wave output that approximates a RMS sine wave (like wall voltage). This is a double square wave with a gap between the negative going and positive going squares. The inverter companies call this "modified sine" which is kind of a misnomer used as a marketing term. The more expensive inverters use a high-frequency Class-D amplifier to produce a more accurate approximation of a sine wave. It's usually not "pure", as it has some amount of harmonic distortion, but for marketing reasons they try to distinguish their product from the "modified-sine" by using the "pure sine" misnomer. The front end of all switch-mode power supplies rectify the incoming AC into DC as a first step in conversion. Step wave rectifies just as well as a normal sine wave! The ONLY reason to run "pure sine" inverters is if you are running sensitive audio gear with linear power supplies, as step-wave will induce a buzzing noise in the audio signals whereas the smoother approximation will not. Don't believe the hype that the "pure sine" inverter companies promote, it simply isn't true. The only things that are dangerous to run on step-wave are things with triac devices or capacitor-based power supplies. This includes things like Dewalt power tool chargers, light dimmers, etc. If it's extremely light (feels like there's nothing in it), and/or it has a 120V rating only, then it's probably not safe for step-wave use. Dewalt chargers have been known to fail and overheat on step-wave! If your power supply has a wide input voltage, such as almost all laptop supplies (100-240v), it is a universal switch mode supply and therefore safe. This includes most small electronics chargers, like for phones, iPods and cameras. If the voltage requirement reads only 120V and it's NOT a heavy "wall-wart" type supply, it's probably not safe. Check your nameplates! If your device has sound such as a TV or Stereo and it emits a buzzing sound out of it's speaker when you run it on step-wave, then that's not harmful, but is an annoying side-effect. You can buy the more expensive "pure-sine" model if this is undesirable.


How long did it take the Millennium Falcon to make the Kessel Run?

Han Solo claimed the Millennium Falcon can make the Kessel Run in twelve parsecs. You will note though that "parsecs" is a unit of distance. So, if Captain Solo's claims are true, he may mean that the Falcon can make the Kessel Run in a shorter distance than what is known.


How many Ohio soldiers buried at Normandy war cemetery?

Soldiers buried in the Allied War Cemeteries are not identified by state, only by name and the unit they fought in. You can possibly find out more information from sites run by the War Graves Commission.


What is Purpose of the electronic control unit?

Electronic Control Unit or ECU usually controls the engine, transmission, or body controls. Modern cars have three of these units for the above mentioned areas. The ECU most commonly is referring to controlling the engine and emission controls. It supplies the engine with the proper fuel, spark, and timing, to make the engine run and perform efficiently without too much pollution.


What is the duration of Run Fatboy Run?

The duration of Run Fatboy Run is 1.67 hours.

Related Questions

Should I Buy a Modified or Pure Sine Wave Inverter?

Many people are unsure of the differences between a modified or pure sine wave inverter. Think of a modified sine wave inverter as a set of stairs. You will get power in blocks and there will be times when the output is sketchy. A pure sine wave inverter provides power much like the power provided by an electric company. Pure inverters provide smoother and more reliable power waves than a modified inverter. A modified inverter is less expensive and can run smaller items, such as a coffee maker or microwave. However, you may want to consider investing in a pure inverter if you want to run larger items, like a computer or television. Electronics that tend to draw a lot of power should always be run on a sine wave inverter for consistency and safety.


What size of inverter do you need to run a mini refrigerator or a typical bar refrigerator?

for modified sine wave inverter (most common type, if it doesn't say than it's modified sine) a safe bet would be the 1,000 watt inverters or higher because the mini fridge will surge 3-5 times its continuous rated wattage for anywhere from 1-10 seconds. so although your fridge only needs 90-150 watts to run it might burn out an inverter say in the 150-300 watt range. a modified sine wave 1,000 watt inverter is about $65-100. you are supposed to buy pure sine wave inverters for a fridge, but those are expensive. you do run the risk of ruining the fridge faster if you do not run pure sine wave , however.


Why ceiling fans generally make noise when run by inverter?

Most of the inverters cant reproduce proper Sine Wave.They are usually producing modified square waves.Some high cost inverters can produce pseudo sine wave(more similar to sine wave). The fans field windings are designed to produce proper revolving field only with standard sine wave.When using modified square wave the field produced will be jerky.These jerks are the main reason of sound.The un-filtered harmonics in the produced wave is also a factor


Do sine wave inverters affect electronic equipment?

A sine wave inverter is used to run an electronic device from a battery when the device is something that needs sine-wave AC to operate. So, in the sense that the inverter makes the device run properly, I guess you could say that it 'affects' the device.


Discuss the three types of inverters?

1.Square wave: This is one of the simplest waveforms an inverter design can produce and is useful for some applications. 2.Sine wave: A power inverter device which produces a multiple step sinusoidal AC waveform is referred to as a sine wave inverter. To more clearly distinguish the inverters with outputs of much less distortion than the modified sine wave (three step) inverter designs, the manufacturers often use the phrase pure sine wave inverter. Almost all consumer grade inverters that are sold as a pure sine wave inverter do not produce a smooth sine wave output at all, just a less choppy output than the square wave (one step) and modified sine wave (three step) inverters. In this sense, the phrases pure sine wave or sine wave inverter are misleading to the consumer. However, this is not critical for most electronics as they deal with the output quite well. Where power inverter devices substitute for standard line power, a sine wave output is desirable because many electrical products are engineered to work best with a sine wave AC power source. The standard electric utility power attempts to provide a power source that is a good approximation of a sine wave. Sine wave inverters with more than three steps in the wave output are more complex and have significantly higher cost than a modified sine wave, with only three steps, or square wave (one step) types of the same power handling. Switch-mode power supply (SMPS) devices, such as personal computers or DVD players, function on quality modified sine wave power. AC motors directly operated on non-sinusoidal power may produce extra heat, may have different speed-torque characteristics, or may produce more audible noise than when running on sinusoidal power. 3.Modified sine wave: A modified sine wave inverter has a non-square waveform that is a useful rough approximation of a sine wave for power translation purposes. The waveform in commercially available modified-sine-wave inverters is a square wave with a pause before the polarity reversal, which only needs to cycle back and forth through a three-position switch that outputs forward, off, and reverse output at the pre-determined frequency.Switching states are developed for positive, negative and zero voltages as per the patterns given in the switching Table 2. The peak voltage to RMS voltage do not maintain the same relationship as for a sine wave. The DC bus voltage may be actively regulated or the on and off times can be modified to maintain the same RMS value output up to the DC bus voltage to compensate for DC bus voltage variation. The ratio of on to off time can be adjusted to vary the RMS voltage while maintaining a constant frequency with a technique called PWM. The generated gate pulses are given to each switch in accordance with the developed pattern and thus the output is obtained. Harmonic spectrum in the output depends on the width of the pulses and the modulation frequency. When operating induction motors, voltage harmonics are not of great concern; however, harmonic distortion in the current waveform introduces additional heating and can produce pulsating torques. Numerous electric equipment will operate quite well on modified sine wave power inverter devices, especially any load that is resistive in nature such as a traditional incandescent light bulb. Most of the AC motors will run on MSW inverters with an efficiency reduction of about 20% due to the harmonic content. However, they may be quite noisy. A series LC filter tuned to the fundamental frequency may help.


Can a generator run a cental air unit?

While most modern central air systems DONT require much power you should be careful that the generator that you use puts out a clean 60hz sine wave or at least modifed sine wave. Basically you should use a generator that is safe to run a computer on. Other than that a residential unit should draw less than 15amps on start and 1500w+/_ so I would say figure for 2000w to be safe


What is Quasi Square wave or Modified Square wave Inverters?

Quasi Square Wave or Modified Square Wave actually mean the same thing. Modified square wave is the actual wave form. Quasi Square Wave is a marketing term used by many low cost inverter manufactures. Inverters convert Direct Current DC to Alternating Current AC. Old obsolete inverter technology created square wave output. As stated by the name the wave form is square not sinus as required to have pure sine wave AC. Modified square wave has a step or dead space between the square waves. This reduces the distortion or harmonics that causes problems with electrical devices. Modified Square Wave inverters will work fine for pure resistive loads, like lamps or heaters. It will also work well with pure inductive loads, like universal motors in mixers and blenders. If these devices have electronic speed control this could be damaged. Devices that have transformers in their power supplies, Microwave Ovens, TVs, Computers etc. will run hotter and less efficient. These devices will not last as long as the would on pure sine wave inverters. For the money the modified square wave inverter will cost more in the long run by reduced efficiency and possible damage to appliances. I highly recommend that you use a pure wave inverter it will cost less by increased efficiency, problems and possible damage to your appliances.


Is square wave inverter harmful to electronic devices?

Depends on the device. For instance almost all laptop power supplies use a international (aka universal) switch mode power supply. They don't care about modified sine wave output at all! Almost all low-cost inverters use a step-wave output that approximates a RMS sine wave (like wall voltage). This is a double square wave with a gap between the negative going and positive going squares. The inverter companies call this "modified sine" which is kind of a misnomer used as a marketing term. The more expensive inverters use a high-frequency Class-D amplifier to produce a more accurate approximation of a sine wave. It's usually not "pure", as it has some amount of harmonic distortion, but for marketing reasons they try to distinguish their product from the "modified-sine" by using the "pure sine" misnomer. The front end of all switch-mode power supplies rectify the incoming AC into DC as a first step in conversion. Step wave rectifies just as well as a normal sine wave! The ONLY reason to run "pure sine" inverters is if you are running sensitive audio gear with linear power supplies, as step-wave will induce a buzzing noise in the audio signals whereas the smoother approximation will not. Don't believe the hype that the "pure sine" inverter companies promote, it simply isn't true. The only things that are dangerous to run on step-wave are things with triac devices or capacitor-based power supplies. This includes things like Dewalt power tool chargers, light dimmers, etc. If it's extremely light (feels like there's nothing in it), and/or it has a 120V rating only, then it's probably not safe for step-wave use. Dewalt chargers have been known to fail and overheat on step-wave! If your power supply has a wide input voltage, such as almost all laptop supplies (100-240v), it is a universal switch mode supply and therefore safe. This includes most small electronics chargers, like for phones, iPods and cameras. If the voltage requirement reads only 120V and it's NOT a heavy "wall-wart" type supply, it's probably not safe. Check your nameplates! If your device has sound such as a TV or Stereo and it emits a buzzing sound out of it's speaker when you run it on step-wave, then that's not harmful, but is an annoying side-effect. You can buy the more expensive "pure-sine" model if this is undesirable.


Can a transformer run on a higher-than-zero sine wave?

Well first of all DC does not have a sine wave. DC current is one direction only and would appear as a flat line on a graph. Second no DC doesn't not work on a transformer because it becomes saturated at a constant level. You need oscillating voltages to pass through a transformer.


Can a modified sinewave inverter run a television and a demostic heating pump and and burner?

Work out the total watts of what you want to run on the inverter (rated amps x input voltage) and if the inverter is rated to that many watts it should run the equipment. Best way to find out how the modified wave affects their operation is to try it.


What will happen if a modified sine wave inverter with 115 Volts output is used as a power source wherein a step up transformer is plugged into it to get a power output of 220 Volts?

It will work, but the transformer will not be able to supply its full rated load, because of the harmonic distortion of the non-sine wave output of the inverter. The transformer will also probably run a little hotter too. If you are talking a small load fed from a transformer much larger than required, probably nothing to worry about. But if the power level is large, or you are loading the transformer to more than 30 or 40% of its rated VA, you could run in to trouble. Monitor voltages and temperatures carefully (and have a fire extenguisher handy...)


Can a car run on crisco?

A specially modified diesel can run on Crisco.