answersLogoWhite

0


Best Answer

Go to your local GM dealer and if your real nice, one of the tech's will let you make a copy of the wiring diagram from his tech manual. The Hayne's manuals that you can buy on e bay or auto zone also have electrical schematics but from my experience are not always accurate. The heated seats in the Silhouette were prone to failure from side seat flexing. Your's probably doesn't work because the heating element itself is damaged. The new replacement elements do not cover the side seat area, do not flex, and therefore will not have this failure. I have been told that the upper heating elements are OK but are wired in series with the bottom element. If one open's the circuit then neither one will heat. Good luck. Go to your local GM dealer and if your real nice, one of the tech's will let you make a copy of the wiring diagram from his tech manual. The Hayne's manuals that you can buy on e bay or auto zone also have electrical schematics but from my experience are not always accurate. The heated seats in the Silhouette were prone to failure from side seat flexing. Your's probably doesn't work because the heating element itself is damaged. The new replacement elements do not cover the side seat area, do not flex, and therefore will not have this failure. I have been told that the upper heating elements are OK but are wired in series with the bottom element. If one open's the circuit then neither one will heat. Good luck.

User Avatar

Wiki User

16y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Does anyone have a wiring diagram for an Oldsmobile Silhouette drivers side heated seat Mine stopped working and you need to trace down the wires Thanks in advance?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you replace the headlight in a 2003 Oldsmobile Silhouette?

how do i replace the drivers side headlight in a 2003 oldsmobile silhoutte


What is the firing order for a 2000 Oldsmobile silhouette?

The firing order for the 3.4 V-6 is 1-2-3-4-5-6The cylinder are numberedfrom the firewall, passenger to drivers side 1-3-5.From the radiator, passenger to drivers side 2-4-6.On the coil pack from passenger to drivers side5-2-3-6-4-1


Need parts diagram of 2000 drivers door?

i need parts diagram for2000 Pontiac Montana drivers side door


Where can you find a fuse diagram for a 2000 Oldsmobile alero?

Either at the fuse panel at the left of the dash board, or on the cover of the black fuse/relay box located under the hood drivers side near fire wall.


Where is the neutral safety switch located on a 2000 Oldsmobile silhouette?

I found it on top of the transmission next to the shift lever. I can see it by going under the van just behind the drivers front tire. Or by removing the rubber intake duct that is between the air felter box and the throttel body.


How can you tell if the quad drivers are bad in a 1991 Oldsmobile Cutlass Ciera S?

Need to know what quad drivers are...


Where is the starter on a 1998 Oldsmobile 88?

Front, drivers side , below engine


Where is the wiper motor for a 1992 Oldsmobile 98?

On the drivers side engine firewall.


How do you fix drivers side window for a 1997 olds silhouette?

I have a 2000 oldsmobile and i had this problem with the drivers side. come to find out it was the switch and not the motor. If you check with a local junk yard you can pick up a good one for half the cost. I did replace the window motor but it still didnt work. i recommend the switch first then if that doesnt fix it then invest in teh window motor. save urself some money.


Where is the Relay located for the power windows in a 1997 Oldsmobile Aurora?

Most of the relays for the 1997 Oldsmobile Aurora are under the back seat on the drivers side.


Where is cylinder 1 on an Oldsmobile 350 engine?

Front cylinder, drivers side of engine.


How do you replace the drivers side headlight in a 2001 Oldsmobile Silhouette?

You remove the three plastic thumb screws and the headlamp it will come out along with the marker light, On the back of it will be a big plastic round cover turn it 1/4 turn and carefully pull it out. BE CAREFUL NOT TO TOUCH THE NEW BULB THE OIL ON YOUR FINGERS WILL SHORTEN THE LIFE OF THE BULB