First, you need tools:
1. Flat blade screwdriver or butter knife
2. Phillips screwdriver (#2)
Second, you leave key out of ignition and everything OFF
Then, you take the screwdriver or butter knife and carefully pry away the plastic ring that surrounds the radio and heater/AC controls. There are 6 (six) clips under the ring, two on each side and one on top and another on the bottom. Once you have the ring off, you can see that there are 8 (eight) screws holding the radio and heater/AC controls in place. You have to remove all of them in order to take out the radio.
Once you have all 8 (eight) screws removed you can carefully pull both the radio and heater/AC controls out. On the back of the radio are three connections, the one on your left is removed by squeezing the top and bottom of the connector and slowly pulling on the connector until it comes out. The next connector is smaller and is removed in the same manner. The last connector is for the radio antenna and comes out by pulling it.
Now you have the radio out and removed!!
You can then install a new radio if you have all the adapters and wiring harness adapters and wiring diagrams. ... or you can put the radio back in.
I pulled my radio out to add a Sirius Satellite Radio to the factory system.
To install a radio in a 2001 Chevy Prism, first disconnect the negative battery terminal to ensure safety. Remove the dashboard trim using a flathead screwdriver or a trim removal tool to access the factory radio. Unscrew and disconnect the old radio from the harness, then connect the new radio using an adapter if necessary, and secure it in place. Finally, reattach the dashboard trim and reconnect the battery.
I had to go to a dealership to get the radio unlocked, also the cause; ( radio locked) was Battery Failure. After I puchased a new battery I found the radio use to be locked.
Newer radios are programmed with the VIN of the car they are in. If you have to replace the radio with a factory radio, you have to take it to your local dealer, and have them reprogram it. They might require you to show proof that the new radio is bought, and not stolen thou. But the new radio has to be unlocked thru the OBD2 port thru a GM scanner.
take the old one out noting if it has a wiring harness from the auto wiring to mate to the radio harness ie male/female connectors, if so cut the harness from the old radio and splice to the new radio soldering or electrical tape connections following the color coded diagram that comes with the new radio. If the harness is not already there buy a new one for make/model of auto and install. Plug in harnesses to each other and install new radio after connecting the antennae.
,. .its under the hood under a cover. Its in a group of fuses, look under the cover & you will see their designations. . . it will be a 10 or 15 amp fuse. . & yes it is for both clock & radio. . if your radio works & the clock is still out, you will need a new radio. . .Good Luck. .
Connect the wiring harness on the back of your new radio. Slide the radio into the radio slot. Tighten down the radio retaining screws.
Remove the wheel. Next, remove the springs and the retaining clips. The brake pads will come off. Reverse the process to install the new brakes.
In a new Chevy Uplander a four-speed automatic transmission is standard, but buyers may purchase the optional available all-wheel drive. This is only available with the extended wheelbase model.
I need to replace the after market radio/cd player in a 2003 Chevy Cavalier. How do I get the existing radio out and install a new one. How do you remove the dash trim without damaging the retainer clips and all the other plastic parts, then install the new after market radio/cd player?
Remove the front cover of your 1979 Chevy Corvette radio. Remove the radio retaining screws. Slide the radio out. Remove the wiring harness and the antenna cable from the back of the radio. Reverse the process to install the new radio.
Because not that many people were buying it and the style was getting old, and Chevy did not want to waste money for a new model if there would be few buyers
To install a radio in a 2001 Chevy Prism, first disconnect the negative battery terminal to ensure safety. Remove the dashboard trim using a flathead screwdriver or a trim removal tool to access the factory radio. Unscrew and disconnect the old radio from the harness, then connect the new radio using an adapter if necessary, and secure it in place. Finally, reattach the dashboard trim and reconnect the battery.
It is not necessary to remove the dash. Only necessary to remove enough of the trim pieces to get the radio out. If you look carefully you will see what needs to be removed.
How do you install a new heater core on a 1979 chevy monte carlo?
Pull out the ashtray and pop out the panel covering your stock radio, a/c, & tape player. It just snaps out. Unscrew the 2 screws holding the factory radio in. Install your after-market radio and pop the cover panel back on. Seems almost to easy right?
You pull out the Stock radio and buy a box to put in in then remove the center dash peice by pulling the bottom and cafully the top. then you can undo the wireing clip behind that and by a new center peice that is made for a radio.
the dash panels just pop off but you will have fun getting the switches off