The radio code should be on a credit card which is in the car's documentation
If you don't have the code then contact your local Jaguar dealer, they should be able to look up the code on their computer using the VIN
Once you have the number......
Turn the key in the ignition until the warning lights shoe
Switch on the radio by turning the on/of knob clockwise
The radio should be blank
Enter the 4 digit code using the preset buttons.
If an incorrect code has been entered......
Hold the CATS button for at least 3 seconds, the number should disappear
Enter the correct number
You only have 3 goes to get it right - if you've entered 3 incorrect numbers you'll need to contact your Jaguar dealer to find out how to release the radio,. This may involve:
- disconnecting the battery
- reconnecting the battery
- running the car for at least an hour
- repeating the steps above
To remove the secure mode from a Nissan Tino radio, you typically need to enter a specific security code. First, turn on the radio, and it should prompt you for the code if it's in secure mode. If you have the code, enter it using the radio buttons. If you don't have the code, you may need to consult your vehicle's manual or contact a Nissan dealer for assistance.
To take a Bentley Arnage radio off safe mode, you typically need to enter a security code. This code is usually provided in the owner's manual or can be obtained from a Bentley dealership. After powering on the radio, follow the prompts to enter the code. If you don't have the code, it's best to consult your dealership for assistance.
To remove the "SAFE" mode from a Chevrolet utility radio, you typically need to enter the correct security code. This code is often found in the owner's manual or provided by the dealership. Turn on the radio, and when "SAFE" appears, press and hold the "AM/FM" button and the "Seek" button simultaneously until the display prompts you to enter the code. After entering the correct code, the radio should unlock and resume normal function.
To enter the radio code for a Seat Leon, start your vehicle and turn on the radio, which will display a "SAFE" or "CODE" message. Use the preset buttons (1-4) to input the code: press the first button for the first digit, the second button for the second digit, and so on. Once the code is fully entered, press the "MODE" or "OK" button to confirm. If entered correctly, the radio should unlock and resume normal operation.
I just purchased a 2009 Jetta SE and the radio was in SAFE 2 mode. The dealer tried the radio code but could not get the radio to a point to enter it. I read a number of threads and tried many suggestions, leave the car in the Aux mode for an hour, hold down the seek and mode buttons etc. Finally I disconnected the battery waited a few moments and re-connected. I figured maybe this would show me the screen to enter the code but instead the radio booted up with no code and works fine. The dealer suggested I return when the service dept was open, none of the sales people had a clue.
You need your operator's folder. In there is a booklet about the radio. it will have a code you need to enter to get the radio out of "safe" mode. the code is unique to each radio and car.
To enter the radio code for a 2003 VW Jetta, first turn on the ignition and then the radio. The display will show "SAFE" or "LOCK." Use the preset buttons (1-4) to input the code, pressing the corresponding button for each digit. After entering the full code, press the "MODE" or "OK" button to confirm and unlock the radio.
To get the radio out of safe mode on a 2003 Vauxhall Corsa SXI, you typically need to enter a security code. If you don't have the owner's manual, you can try checking the glove compartment, inside the trunk, or contacting a Vauxhall dealership to retrieve the code using your vehicle’s VIN. Once you have the code, turn on the radio, and when it displays "SAFE," enter the code using the preset buttons. If you enter the code incorrectly multiple times, the radio may lock, requiring you to wait before trying again.
To enter the VW radio code while in safe mode, first, turn on the ignition and the radio. You will see "SAFE" displayed, prompting you to enter the code. Use the preset buttons (1-4) to input the code; typically, you press the corresponding button for each digit of the code. If entered correctly, the radio will unlock and start functioning normally.
Your owners manual will have the code. Hold down the mode and scan buttons at the same time then enter the code using the # buttons.
To remove the secure mode from a Nissan Tino radio, you typically need to enter a specific security code. First, turn on the radio, and it should prompt you for the code if it's in secure mode. If you have the code, enter it using the radio buttons. If you don't have the code, you may need to consult your vehicle's manual or contact a Nissan dealer for assistance.
i have brought a car but the radio is showing safe mode and unfortunately i do not have a code are you able to supply the code radio is blaupunk 300 car is a vauxhall zafira 2002
To take a Bentley Arnage radio off safe mode, you typically need to enter a security code. This code is usually provided in the owner's manual or can be obtained from a Bentley dealership. After powering on the radio, follow the prompts to enter the code. If you don't have the code, it's best to consult your dealership for assistance.
To enter the radio code on a 1999 Audi A8 Concert radio, first turn on the radio, which will display "SAFE" if the code is required. Press the "TP" button to enter the code mode. Use the radio preset buttons (1-4) to input the code: each button corresponds to a digit. After entering the complete code, press the "TP" button again to confirm, and the radio should unlock and start working.
Press and hold down the "mode" button until the radio beeps, then enter the code. I can't remember if you have to press "mode" again after entering the code or not, but i don't think so. If you don't know the code to your radio you will have to go into a L.R. dealership and they can tell it to you.
Turn the ignition to the on position but do not start the engine. Leave it sitting like that for one hour. The radio should then switch out of safe mode and allow you to enter the correct code.
To enter the radio code on a 2000 Audi A4 Quattro, first turn on the ignition and the radio. If the radio displays "SAFE," press the "TP" button to enter the code mode. Then, use the station preset buttons (1-4) to input the code by pressing the corresponding button for each digit. Once the code is entered correctly, press the "TP" button again to confirm and unlock the radio.