0
What else can I help you with?
How do you draw hexagon using repeat command of logo?
To draw a hexagon using the repeat command in Logo, you can use the following code: repeat 6 [forward 100 right 60] This command will move the turtle forward by 100 units and then turn it right by 60 degrees, repeating this process six times to create a hexagon. Adjust the forward distance to change the size of the hexagon.
How do you draw a triangle using repeat command in logo?
To draw a triangle using the repeat command in Logo, you can use the following code: REPEAT 3 [FORWARD 100 RIGHT 120] This command instructs the turtle to move forward 100 units and then turn right by 120 degrees, repeating this process three times to complete the triangle. Adjust the forward distance as needed for different triangle sizes.
Does grateful dead's skull logo spell out the band name?
The official logo of Grateful Dead using the skull in the center does spell out the band's name. It is the word 'Grateful' in a semicircle on the top of a skull in a circle and 'Dead' in a semicircle across the bottom of the circle. A few variations of this logo were used on different album covers for the Grateful Dead.
When did YTV stop using a YTV Stereo logo?
Around 2003-2004 most shows used stereo logos during mid 80's thru mid 90's
Does Chris Brown have a logo?
Yes
How do you draw nonagon using logo command?
repeat 3 [fd 250 rt 120]
How do you draw hexagon using repeat command of logo?
To draw a hexagon using the repeat command in Logo, you can use the following code: repeat 6 [forward 100 right 60] This command will move the turtle forward by 100 units and then turn it right by 60 degrees, repeating this process six times to create a hexagon. Adjust the forward distance to change the size of the hexagon.
How do you draw a triangle using repeat command in logo?
To draw a triangle using the repeat command in Logo, you can use the following code: REPEAT 3 [FORWARD 100 RIGHT 120] This command instructs the turtle to move forward 100 units and then turn right by 120 degrees, repeating this process three times to complete the triangle. Adjust the forward distance as needed for different triangle sizes.
What is the logo command for drawing the alphabet H?
In Logo programming, you can draw the letter "H" using the following commands: FORWARD 100 BACK 50 RIGHT 90 FORWARD 50 LEFT 90 FORWARD 50 BACK 100 This sequence moves the turtle to create two vertical lines with a horizontal line connecting them. Adjust the distances as needed for your desired size.
How do you draw rectangle in logo with repeat command?
In Logo, you can draw a rectangle using the REPEAT command to create the four sides efficiently. For example, you can use the following code: REPEAT 2 [ FORWARD 100 ; length of the rectangle RIGHT 90 FORWARD 50 ; width of the rectangle RIGHT 90 ] This code moves the turtle forward to draw the length, turns right, and then draws the width, repeating the process to complete the rectangle.
What is the logo command for rhombus?
In Logo programming, the command to draw a rhombus can be achieved using the combination of FORWARD and RIGHT (or LEFT) commands to create the desired angles. A typical command sequence might look like this: REPEAT 2 [FORWARD 100 RIGHT 60 FORWARD 100 RIGHT 120], where you adjust the angles and lengths as needed to create a rhombus shape.
What is SETH command used for in logo?
SETCH command is used to point the command its head in any direction without using the RT or LT.
How do you draw an octagon using Logo command?
An octagon is an eight-sided pentagon where all sides are equal length and all angles are equal. To draw an octagon in Logo, you move forward the length of a side and then turn 45 degrees, repeating 8 times (8x45=360). The following will therefore draw an octagon with a side length of 100 pixels: repeat 8 [fd 100 rt 45]
How do you make a trapezium in MSW logo?
Well, honey, to make a trapezium in MSW Logo, you gotta use the "FD" (forward) and "RT" (right turn) commands to draw the sides of the trapezium at different lengths and angles. Just remember to keep track of your angles and side lengths to get that trapezium looking sharp. And if you mess up, just hit that "CLEARSCREEN" command and start over - ain't nobody got time for crooked trapeziums!
How do you make a flag in msw logo using repeat command?
To create a flag in MSW Logo using the repeat command, you can use the following steps: First, define the size and colors of the flag sections. Then, use the REPEAT command to draw rectangles that represent each section of the flag. For example, you can use REPEAT 3 [FORWARD 100 RIGHT 90 FORWARD 50 RIGHT 90] to create three horizontal stripes. Adjust the dimensions and colors as needed to achieve your desired flag design.
What is the Logo command for drawing the alphabet R?
fd 60,bk 30,rt 90,fd 30,lt 90,fd 30,bk 60
How do you make circle in msw logo using repeat command?
repeat 360[fd1 lt 1]
