0
Okay....first you take a sheet of paper and you begin by starting in the middle of the sheet with a pencil. You start to make a circle approximately 2 inches or even slightly smaller. As you begin to reach the end of the circle, do not close it, instead begin to make another circle and do not close that circle and then begin again. You should see a swirl pattern forming from your circles. Do not make the circles too close together. Try to keep at least an inch or more between them. When you reach the end of the paper, take a pair of scissors and begin cutting from the inside circle, along the lines. Do not cut the final circle. When you allow the inner pieces to fall free, it will make a huge circle that you can actually step through from the chain of paper. This is a math game in many elementary math books. Be sure to make the swirly pattern without closing the circles completely or it will not work. Good LucK! Hope this helped!! I wish I could draw the pattern for you. It is fun to do with children!!!
What else can I help you with?
Who's song is 'I want to make you sweat'?
UB40 Its actually by Inner Circle.
Can you make a saxophone out paper?
yes. yes you can. i believe in you young skywalker
How do you make Jessie j wigs with paper?
you can't and if you can it would look awful>:<
What does flute pad cleaning paper do?
Flute pad cleaning paper is used to clean dirt and grime from the pads on the flute. When dirty these pads will tend to stick which may make the flute difficult to play. Flute pad cleaning paper can be used to clean the dirt from these pads and make them respond like normal. Follow the link below on some helpful tips on the use of flute pad cleaning paper.
When was Delusions of Grandeur - Circle II Circle album - created?
Delusions of Grandeur - Circle II Circle album - was created on 2008-04-25.
How do you make a paper guitar?
scrunch it up in a circle and then make a rectangle and then stick it together
How do you make a model of an empty 3 dimensional circle?
paper mache
How do you make paper pattern quarter circle with 18 inch radius?
Make circle with 18 inch radius, fold in half, fold in half.
How do you use filtration paper?
fold it in half make it a circle put it in a funnel
How do you make paper bats?
all you have to do is cut out 2 hands out of paper and cut out a circle in the middle and add detail loe
How do you make a circle with a dot in the middle with out taking you pencil of the paper?
u can't , its imposible.
How can you make a circle by filling up the paper with only parallel lines?
Roll up the paper so line ends touch.
How can you make a good paper bridge?
You can't really make a strong paper bridge. Unless you use poster paper or very thick, but flexible paper. If you do, this is how: 1.Get paper, pencils, scissors, and glue/ tape 2.Cut a circle - which is hollow. Cut the circle in half. 3. cut along rectangle about as long as the width on the half circle. 4. Glue/Tape the half circle with the rectangle in the middle of the half circle "rounded" 5 Repeat procedure 4 with the other side of the long rectangle and the other half circle.
How do you build a cylinder?
Cut a circle from a piece of paper. The paper has thickness so, that makes the circle that you cut from the paper a cylinder.
What are the directions to make a paper flower?
Paper flowers, like real flowers can be in many different forms. A simple way would be to use 2 contrasting colors of a thick paper (like construction paper). Cut one of the papers into circles of descending size. Glue the smallest circle onto the circle that is the next size up and continue until all circles are used. Then make one circle in the contrasting color in one small circle and glue that one top.
How do you draw a fermata?
you can't draw a fermata on the computer but to draw a fermata on paper you would make a half circle with a dot inside of the half circle
How can you make a cone out of paper?
To make a cone out of paper, start by cutting a sector from a circle. Then, overlap the cut edges to form a cone shape and secure them with glue or tape. Finally, trim the base of the cone to make it even.
