0
According to the Service manual for that year you need to remove the compressor shaft bolt. A band-type oil filter wrench may be used to hold the assembly still. Once the bolt is removed, tap the clutch plate with a plastic or non-metal hammer to disloodge the plate from the splines on the compressor shaft. Now you should see the pulley. There is a snap-ring holding it on. Use a pair of straight-tip pliers to remove the ring. The pulley should be able to come off at this point.
Wiki User
∙ 17y ago
Wiki User
∙ 17y agofour easy bolts/nuts Everyone should have a manual for their vehicle, and the library should have a professional shop manual available in the reference section(make copies of the right sections) read up and fix it like a PRO! :) good luck
Wiki User
∙ 15y agoThe fan and clutch are fastened to a pulley with a large size hex nut which you will see directly behind the fan (toward the back of the vehicle). The trick here is to get a wrench on that nut and try to loosten it counter clockwise while holding the pulley steady with a 'special tool'. The problem here is that even with the special tool it's difficult to do. What I did was take the vehicle to a local shop and asked them to loosen it. The mechanic did it with a special air wrench attachment and it didn't look too easy. Once the fan/clutch assembly is removed from the vehicle you will find it easy to transfer the fan to the new clutch and reattach the assembly to the pulley without special tools. Good luck.
Wiki User
∙ 14y ago1. Recover refrigerant properly.
2. Remove serpentine belt.
3. Remove air cleaner box-- must remove 3 nuts from below. Bolts are captive with rubber
bushings.
4. Disconnect steering shaft at U-joint. Retract it toward firewall and set it to the side.
5. Remove refrigerant lines from compressor.
6. Disconnect connector for electric clutch (slide red lock, push unlock tab at rear of connector).
7. Disconnect supports (top and bottom of engine) for refrigerant lines (just gives them more wiggle
room).
8. Remove 3 mounting bolts from compressor. When it drops down, also remove mounting bracket
from side of engine.
9. Compressor can now be manipulated to be removed.
Installation of new compressor is the reverse. Replace O-rings on lines, etc. Make sure to not connect
clutch connector until after system is properly charged with refrigerant and oil.
--- Cris
Wiki User
∙ 8y agoIt's easier, faster, and more often than not, cheaper to replace the entire compressor.
Wiki User
∙ 16y agoremove fan belt fan clutch scres off the water pump this is usually a left hand thread so in this case it will be righty loosy lefty tighty remove fan blades before you remove fan clutch
Add your answer:
Earn +20 pts
Will a 1999 Jeep Grand Cherokee Laredo with a 4.0 transmission fit a 1999 Jeep Grand Cherokee Laredo with a 4.7?
No, they will not interchange.
What year transmissions are interchangeable with a 1999 Jeep Grand Cherokee Limited?
The most compatible and completely interchangeable transmission that can be used with a 1999 Jeep Grand Cherokee Limited is the 45RFE transmission. This is from a 2000 Jeep Grand Cherokee. Only this model year is compatible with the 1999 model year as the vehicles shared 127 of the exact same parts.
Will a 2000 to 2004 jeep grand Cherokee limited v8 power steering gear box fit on 1999?
To find out if a 2000-2004 Jeep Grand Cherokee power steering gear box will fit on a 1999 Jeep Grand Cherokee, call your nearest DIY auto parts store
Will a 1998 Jeep Grand Cherokee transmission fit a 1999 Jeep Grand Cherokee?
It may fit, but it is not plug and play. The computer and trans systems are different.
Does the key for a 1999 Jeep Grand Cherokee Laredo have a chip in it?
If it is gray, then yes.
How do you remove the horn button on a 1999 jeep grand Cherokee?
Very carefully
Instructions to replace a 1999 Grand Prix GTP ac compressor?
To replace the AC compressor in a 1999 Grand Prix you must first remove the AC belt. Then disconnect the negative battery cable before removing the compressor bolts and connectors and removing compressor.
How do you remove a pollen filter from 1999 model grand Cherokee jeep?
It doesn't have one.
What seat will fit into a 99-04 Grand Cherokee?
A seat from a 1999-2004 Grand Cherokee is what fits in a 1999-2004 Grand Cherokee.
What size belt do you need to bypass ac compressor on 1999 jeep grand Cherokee Laredo 4.7 lit?
2 feet
Where is the 1999 jeep grand Cherokee ac drain?
where is the ac drain on 1999 jeep grand cherokee limited
1999 grand Cherokee how do you drain front and rear axels?
You have to remove the differntial covers to drain the fluid.
Will a 1999 Jeep Grand Cherokee Laredo with a 4.0 transmission fit a 1999 Jeep Grand Cherokee Laredo with a 4.7?
No, they will not interchange.
What is the mpg for 1999 Jeep Grand Cherokee?
I get 15 to 17 miles per gallon with my 1999 Jeep Grand Cherokee Lorado.
Are 1996 Jeep Grand Cherokee radiators interchangeable with a 1999 Jeep Grand Cherokee?
No. They are not interchangeable.
Is the catalytic converter for a 1995 Jeep Grand Cherokee interchangeable with the 1999 Jeep Grand Cherokee?
No.
How do you remove the air compressor from a 1999 Grand Am?
Always use safety glasses and gloves! To remove the A/C compressor you must evacuate system & properly dispose of old R-134A. Then unbolt and remove old compressor. (You should be certified to handle R-134A to charge system)
