answersLogoWhite

0

Answerok, there is one piece that is hiding the screws to take the radio out and it might be woodgrain but it might not be , anyways, this piece has 2 little screws one on each side of your ashtray. Take these out and pop the whole piece off, the piece should extend all the way up your radio and your traveller or boost control gauge if you have it and around your heater. There are no screws in the top of the piece, just clips that clip out when you pull on it slightly. Then holding the radio in will be 2 screws on opposite corners of each other take these off and then unplug the plugs in the back of the radio(there should be 3, 2 rectangular ones and one little round one that is your radio antenna. And that's it. I didnt want to attempt doing it but i got bored one day and realized that it is a really easy job to do.
User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Music & Radio

2005 Chrysler 300 radio wiring diagram?

Here is a link that gives numerous vehicle diagrams http://www.modifiedlife.com/2005-chrysler-300-car-stereo-wiring-diagram/


How do you hook up Satellite radio to stock Radio in 2005 Chrysler 300c?

To hook up satellite radio to a stock radio in a 2005 Chrysler 300C, you will typically need a satellite radio tuner compatible with your vehicle. You'll also need an FM modulator or an auxiliary input adapter if your stock radio lacks direct inputs. Install the tuner according to the manufacturer's instructions, connect it to the vehicle's power source, and then tune your stock radio to the designated frequency or input for the satellite signal. Finally, secure the antenna on the vehicle's roof for optimal reception.


Install satellite radio in a 2005 Nissan altima?

To install satellite radio in a 2005 Nissan Altima, you'll need a satellite radio receiver and a compatible vehicle adapter kit. First, remove the dashboard panel to access the radio and disconnect the factory unit. Connect the satellite radio receiver using the adapter kit, ensuring proper wiring and antenna placement for optimal signal. Finally, reassemble the dashboard and test the satellite radio for functionality.


How do I access the antenna input on 2005 Sequoia radio?

To access the antenna input on a 2005 Toyota Sequoia radio, you will need to remove the radio from the dashboard. Start by carefully prying off the trim panel surrounding the radio using a trim removal tool. Once the panel is removed, unscrew the mounting screws securing the radio, slide it out, and you’ll find the antenna input at the back of the unit. Disconnect the antenna cable if needed for your purpose.


Is the radio in your 2005 Dodge Magnum a satellite radio?

Yes

Related Questions

Where is the reset switch on a 2005 Chrysler Sebring?

A 2005 Chrysler Sebring does not have a reset switch.


Where is the distributor cap located on a 2005 Chrysler Sebring?

A 2005 Chrysler Sebring does not have a distributor.


Does a 2005 Chrysler Sebring have a cabin filter?

No, a 2005 Chrysler Sebring does not have a cabin filter.


How many motor mounts does a 2005 Chrysler Sebring convertible have?

There are four mounts on a Chrysler Sebring.There are four mounts on a Chrysler Sebring.


How do you drain the transmission on a 2005 Chrysler Sebring?

You remove the pan on the bottom to drain.You remove the pan on the bottom to drain.


How do you remove the alarm on a 2005 Chrysler Sebring?

The factory alarm is an integrated part of the computer system of the vehicle and can not be removed.


Does a 2005 Chrysler sebring have a u-joint?

No.


Where is the fuel pump reset on a 2005 Chrysler Sebring?

A Chrysler Sebring does not have a reset switch. The fuel system is computer controlled with relays.


Where is the fuel system shut off switch on a 2005 Chrysler sebring 4 door sedan?

A Chrysler Sebring does not have an inertia or reset switch.


How do you drain the engine oil on a 2005 Chrysler sebring sedan?

You need to remove the engine oil drain plug. It is on the bottom rear of the engine.


Where can you find a carburetor diagram for a 2005 Chrysler Sebring?

the 05 sebring is fuel injected so there is no carbuatr


How do you replace the thermostat in a 2005 Chrysler Sebring?

To replace a thermostat on a 2005 Chrysler Sebring first drain the coolant from the vehicles radiator, the engine must be shut off during this repair. Then follow the main radiator line to the thermostat housing. Remove the housing and replace the thermostat inside. Refill the coolant.