0
What else can I help you with?
How does a metal halide ballast work?
A metal halide ballast works just by transforming the line voltage into much more useful voltage to the metal halide, and by regulating the current so that the bulb will have its useful life at the most.
How do you calculate transformer voltage ratio test?
Secondary voltage / primary voltage
What does partition mean in beyonce?
Beyonce's song Partition refers to the divider that can be lowered or raised and separates the front and back seats of a limo.
Where is the voltage regulator located on a 2004 jeep grand Cherokee with in line 6 v6?
The engine computer is the voltage regulator.The engine computer is the voltage regulator.
ON MY 93 CHEVY LUMINA When the key is turned in the ignition there is a clicking sound but the lights and radio still work any idea of what this is?
Most likely the battery is weak and dying. Enough voltage and current to make the solenoid barely engage (clicking in and out), but plenty of current and voltage for the radio and some of the lights.
What is the voltage d?
voltage divider
What is the difference between voltage divider and potential divider?
its the same
What is a voltage divider circuit?
The voltage divider circuit is a network of two or more components in series, often resistors, between a potential difference. The voltage between the components will be somewhere between the potential difference across the whole network and so divides the total voltage into one or more intermediate voltages.
When a load is connected to the output voltage divider the output voltage will what?
When a load is connected to the output of a voltage divider, the output voltage will typically decrease due to the loading effect. This occurs because the load draws current, which can change the voltage across the resistors in the divider. The extent of the voltage drop depends on the resistance of the load relative to the resistors in the voltage divider. If the load resistance is significantly lower than the divider resistances, the output voltage will drop more noticeably.
How do design a high voltage voltmeter?
Use a voltage divider and an standard high input impedance voltmeter connected to the low voltage output tap of the divider. Just check that: a) the voltage divider has enough resistance to minimize loading of the voltage source (The voltage divider resistance should be as high as possible). b) the voltmeter's input impedance is at least 10-20 times larger than the output resistance (impedance) of the divider. If necessary add a high-input impedance amplifier or a transducer between the divider output and the voltmeter. What is high voltage for you?
What is function of a divider in electrical system?
what is function of a voltage divider in electrical system
What is the voltage divider theorem?
it is aa linear circuit that produces the output voltage from the fraction of its input. It is also known as potential divider.
What is the current that flows through an unloaded voltage divider?
The current that flows through an unloaded voltage divider is very small, close to zero. This is because there is no load connected to the output of the divider, so there is nowhere for the current to flow. The purpose of a voltage divider is to divide the input voltage between the two resistors, not to pass current.
Device used to step voltage up or down?
As transformers do not work with DC., the answer is a voltage divider network (step down) or a voltage multiplier network (step up).
What is the difference between a voltage divider circuit and voltage regulator I was told if the circuit consumes low current then the voltage divider can be used what does that mean?
A: that is true for less current a divider is OK it has to do with the series resistance and loading if the loading is forever fixed and the source is also fixed at a value then a divider can be used no matter what the current is.
What is voltage divider circuit?
The two resistor voltage divider is used often to supply a voltage different from that of an available battery or power supply. In application the output voltage depends upon the resistance of the load it drives.
How does a voltage divider work to distribute voltage across multiple resistors in a circuit?
A voltage divider is a circuit that uses two or more resistors to divide the input voltage into smaller voltages across each resistor. The voltage across each resistor is proportional to its resistance compared to the total resistance in the circuit. This allows for distributing the input voltage across multiple resistors in a controlled manner.
