Yes it is repairable cause my snapped and i got it fixed!
There are actually two types of pegs on a guitar: Tuning pegs Bridge pin pegs There are six of each. A tuning peg is a peg at the top of the guitar and is use to tighten the strings therefore 'tuning' the guitar. A bridge pin peg holds the other side of the string firmly in place.
peg or tuning peg
The knob used for pitch adjustment or tuning on the violin is called the "peg".
yes in the sense that you achieve different tunings , some people tune lower to achieve heavier sounds , some people tune higher for a nicer sound for say folk music or whatever. wikipedia can tell you all the guitar tunings essentially if you want to tune lower do all the strings equally EADGBE - standard E - the most common guitar tuning DGCFAD - standard D - each string is one note lower
For the tuning pegs in the scroll, you can try pushing them in hard while tuning. If that doesn't work - and you are sure that the hole has not become too large or the peg too small for it - then you'll have to find a way to help make it grip its hole better i.e. to increase the friction of the peg in the hole. A good way is to pull the peg out and rub the bow's rosin block all around the stem of the peg to leave a coating of rosin dust on the surface where peg's stem fits into its hole. Some people recommend using pencil graphite but, as that is more of a lubricant than rosin dust, I have have never found that it works as well as some rosin.
There are actually two types of pegs on a guitar: Tuning pegs Bridge pin pegs There are six of each. A tuning peg is a peg at the top of the guitar and is use to tighten the strings therefore 'tuning' the guitar. A bridge pin peg holds the other side of the string firmly in place.
a peg. or a tuning peg
peg or tuning peg
Turning the peg or moving frets makes the pitch (frequency) of a guitar string go higher or lower.
No, as long as the string is attached properly and the tuning peg itself doesn't slip.
It depends on who you ask. some guitarists leave their strings full length, which depends on the company that makes the strings. Others put their hand perpendicular to the neck on the 12th fret, put the string through the bridge, over their hand and through the hole in the tuning peg, then cut the string where it exits the tuning peg. The guitar's model also affects the string length.
Check to see if the small hole in the peg isn't overly sharp or you are putting a "kink" in the string as you are putting it on. The string gets a kink in it when you put it on then as you unwind it to tune down it snaps.
The knob used for pitch adjustment or tuning on the violin is called the "peg".
Thought I've never tried this, I highly doubt using bass strings on a guitar would work. First of all, the bass string likely wouldn't fit inside a guitar's tuning peg. Also, the action on a guitar simply wouldn't work with a bass string. As far as pickups go, I'm not sure what bass frequencies would do to a guitar pickup, but i wouldn't try.
yes in the sense that you achieve different tunings , some people tune lower to achieve heavier sounds , some people tune higher for a nicer sound for say folk music or whatever. wikipedia can tell you all the guitar tunings essentially if you want to tune lower do all the strings equally EADGBE - standard E - the most common guitar tuning DGCFAD - standard D - each string is one note lower
For the tuning pegs in the scroll, you can try pushing them in hard while tuning. If that doesn't work - and you are sure that the hole has not become too large or the peg too small for it - then you'll have to find a way to help make it grip its hole better i.e. to increase the friction of the peg in the hole. A good way is to pull the peg out and rub the bow's rosin block all around the stem of the peg to leave a coating of rosin dust on the surface where peg's stem fits into its hole. Some people recommend using pencil graphite but, as that is more of a lubricant than rosin dust, I have have never found that it works as well as some rosin.
It is possible to fit the guitar strap to it if it has a strap peg. The strap may or may not be too long, however. If your guitar or ukelale does not have a top strap peg, like me, then you can tie a long string or strap behind the strings, above the nut. I reccomend using a wider strap to prevent it from cutting into your shoulder.