0
Milling cutter Explain advantages and disadvantages of the two flutes?
Wiki User
∙ 14y ago
Two flutes have better chip evacuation for softer materials. The disadvatage of them is that number of flutes are the main source of higher feedrates. A four Flute has the possiblility of double the feedrate of two, but if the material is soft four flutes may load up and break.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Who is cutter on mindless behavior?
ME
What cutting tool is made up of piano wire?
egg cutter
Who is cutter jayden Smith or Willow Smith?
Since Im a girl jaden smith is cuter,but if I was a boy I would say Willow is
Why does Demi Lovato wear bracelets?
She slit her wrists because she has had some suicidal thoughts and is under a lot of pressure.
What is the style of crease that Jason Aldean uses on his brush hog hat?
The crown is like a combination of the "cattleman" crease and the "Gus" crease. Its rounded on top with the back being higher than the front. There is a hint of a "cutter" crease present as well. Gary Allan used to crease his crown very similarly.
What is the advantage and disadvantege of milling cutters compared to single point cutter?
advantage and disadvantage of milling cutter
What is a face milling cutter?
Face milling is done with the side of the mill
What is a veritcal milling machine?
Vertical milling machine and horizontal milling comparison, the main difference is the spindle vertical layout, except for different spindle arrangement, table can move up and down, vertical milling cutter with relatively flexible, wider scope. Use cutter, cutter support, drill and so on. Can keyway milling, milling flat and boring.
How does face milling differ from peripheral milling for producing flat surface?
In face milling: a) The axis of the cutter rotation is perpendicular to surface being milled b) The machining is performed by the cutting edges on both the end and outside periphery of the cutter In peripheral milling: a) The axis of the cutter rotation is parallel to the surface being machined. b) The operation is performed by the cutting edges of the outside periphery of the cutter
How do you measure r.p.m of milling cutter?
use a tachometer
How do you Mount a milling cutter?
Strech is a Bell-End
When would one use a milling cutter?
One could use a milling cutter when using a rotary processor to remove material and also to get the best possible surface finish they would want to get.
Advantages and disadvantages about hedgerows?
It can cost Farmers money and can eat up all his profit. Also cutting hedges can take hours and it needs to be done by a professional hedge cutter
Why the large number of tooth in the milling cutter is used for rough cutting?
24
What are the advantages and disadvantages of butt joint?
the strength can be adjusted with the screws that you need to insert when cutting them out with the cutter on the buscuit surface
What is the difference brtween vertical milling machine and horizontal milling machine?
A "horizontal maching center" has a horizontal spindle. With a horizontal spindle, tools stick out the side of the tool holder and cut across the side of a part (workpiece). Horizontal machining centers are far more expensive than equivalent capacity vertical machines, but have several advantages. Usually the tool holder of a horizontal machine is more ridgid. Also,when machining the side of a part, metal chips fall out of the area being cut, leaving an uncluttered cutting area.A "vertical machining center" has a vertical spindle. With a vertical spindle, tools stick straight down from the tool holder, and often cut across the top of a part. One disadvantage of vertical machining is that when tools cut across the top of a part, the metal shavings, called "chips," often pile up around the tool and interfere with the cutting action. However, vertical machining centers are more common, primarily because they are less expensive than equivalent capacity horizontal machines.
What are the milling machine accessories?
Machine tool accessories with different models are not the same. Like this machine：Lm1450c universal Milling machine. standard accessories ：Milling chuck,milling vice,horizontal spindle cutter,spanner,crank optional accessories: rotary table,DRO,clamp kit,diving head,plug
