0
What else can I help you with?
What would happen if you tied a piece of string to a spoon and then put the string in your ear?
Well think of the laws of physics and gravity. A spoon is heavy and gravity will pull the string down there for brining the spoon down along with it, with little delay from the obstacle of your ear.
How do you fix a pull string toy when the string comes out?
ask company to fix it
What does p0h mean on a guitar tab?
if on a tab it says 3 |---2p0h3----| |----3--4--2-3| its saying play tab 2 pull off open string hammer on 3
In playing guitar tabs what is pull-off?
Assuming your right handed, it means you are not plucking the string with your right hand fingers or pick - if your using one. For example, place your first finger (left hand) on the first fret, first string. That is an "F" note. Keep your first finger there, while placing your third finger (same hand) on the third fret first string. That's a note of "G". Now, instead of plucking the string with the right hand, pull the first string with the third finger that you have on the third fret. In this way you are actually plucking the string with the third finger. Hope this makes sense to you. If I had to show you how to do this, it would take less than a second. Trying to explain it is much more difficult. Viper1
Can you put nylon strings on a steel string guitar?
A: This can be very unsafe! The design of nylon string guitars is very similar from steel string guitars. To get the best sound from a guitar there is a balance between length and flexibility. Nylon strings are under less tension than steel strings so the top is made thinner and the internal braces are lighter allowing the instrument to vibrate more, giving you better volume. The extra pressure that steel strings put on a nylon guitar can, over time, cause the top to pull up, cause braces to come loose, and even pull the bridge off the guitar! Also, most nylon string guitars do not have internal neck reinforcement (truss rod) like steel string instruments do. This will cause the neck to pull forward causing the distance of the strings from the fret tops to decrease greatly making the instrument difficult to play. The tuning gear rollers on nylon instruments are also different. They are normally made from plastic which will not support the pressure of the steel strings. The shafts may break under the extra pressure. Good answer. But if you have a guitar that you don't care about, the sound is very tinny. Alright mate, enough of that, alright mate alright mate mate.
What is the string that you pull to turn on a ceiling light called?
The string that you pull to turn on a ceiling light is called a pull chain or pull string. It is typically connected to the light fixture and used to control the on/off function of the light.
What is the string thing you pull down to change the speed of a ceiling fan?
The string is called a fan pull chain. It is used to adjust the speed of the ceiling fan by toggling between different speed settings.
How do you get a cap off a guitar so you can change the string?
if you are talking about an acoustic guitar i use the back of a hammer to pull the cap up
How do you tie acoustic guitar strings?
To tie acoustic guitar strings, first insert the end of the string through the hole in the tuning peg. Then, wrap the string around the peg and pull it tight. Finally, tune the string to the desired pitch.
How do you install electric guitar strings?
To install electric guitar strings, first remove the old strings by unwinding them from the tuning pegs. Then, insert the ball end of the new string into the bridge of the guitar. Pull the string through the bridge and up to the tuning peg. Wind the string around the tuning peg, making sure it is tight and secure. Repeat this process for each string, tuning them to the desired pitch.
How do you pour water down a string?
To pour water down a string, you can dip the string into the water and let gravity pull the water down the length of the string. Make sure the string is taut and positioned vertically to allow the water to flow smoothly.
How do you string a classical guitar with nylon strings?
To string a classical guitar with nylon strings, you need to start by removing the old strings. Then, insert the ball end of the new string into the bridge hole and pull it through. Next, wrap the other end of the string around the tuning peg and tighten it. Repeat this process for each string, making sure to tune them to the correct pitch.
How do you replace guitar strings?
As you pull off one string, replace it immediately with another, so you don't get confused. The 1st string is the high E or thin string at the bottom. Go in order 1,2,3,4,5,6. When winding the string make sure on the high strings you go under on the first turn so the rest of the string clamps down. If you do enough turns however, this may not be necessary. Just make sure the string is tight.
How are the wave of bass intruments created?
Bass instruments are basically string instruments. Do this tie both ends of a string in such a way that the string it tight or stretched. Now pull the string down from the middle and leave it. Now pull the string down at 1/4 distance from any end. Next do it from 1/8 th distance. As the distance decreases the number of waves produced in the string increases. At 1/2 the distance . This is how the wave is formed in bass instruments.
What are some examples fixed pulley?
Flag pole you can pull down on the string and the flag will raise up
How to put classical guitar strings on properly?
To put classical guitar strings on properly, first remove the old strings. Then, insert the ball end of the new string into the bridge hole and pull it through. Wind the string around the tuning peg, leaving some slack. Tune the string to the correct pitch and trim any excess. Repeat for the remaining strings.
How to stretch guitar strings properly for optimal tuning stability?
To stretch guitar strings properly for optimal tuning stability, gently pull and stretch each string along its length while tuning up to pitch. Repeat this process a few times until the string holds its tuning. This helps the string settle into place and reduces the likelihood of it going out of tune.
