answersLogoWhite

0


Best Answer
Answer

That is the way it goes. Really about the only way is to remove the fuses one at a time and see when the brake lights go out. If the lights are not working, just pull fuses until you find one that is blown.

Don't forget to check under the hood on the passenger side fender- there's another fuse block there!

Check the brake light switch located above the brake pedal, sometimes they go bad, delicate reed switches inside. when you buy the new part - READ INSTRUCTIONS FIRST!! It's a self adjusting part, and you only get one shot at installation, it's an easy fix. Do NOT push the plunger down on the switch, if you try to reset it you will damage the switch, just follow directions word for word and your golden.

User Avatar

Wiki User

โˆ™ 2009-09-17 00:28:16
This answer is:
User Avatar
Study guides

Add your answer:

Earn +20 pts
Q: Where is the fuse for the brake lights on a Jeep Cherokee if the owners manual says look on the fuse panel cover plate and the cover plate says see owners manual?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Music & Radio

Why stop lights will not work bulbs good no blown fuses Jeep Cherokee not a Grand or a Laredo?

brake relay or sensor


What type of DOT brake fluid does a 1992 Jeep Laredo Require?

as it states in the owners manual- Mopar Brake Fluid or equivalent marked FMVSS No. 116, DOT-3 and SAE J1703.


Where is the fuse panel for the brake lights located on a 1999 Jeep Cherokee?

The fuse for the brake lights is in the engine compartment fuse box, located behind the battery. Open the lid. Several fuses are marked but many are not. There is a group of 12 fuse sockets in the middle of the panel, arranged in 3 rows and 4 columns. The brake light fuse is in row 2, column 2. It powers left, right and middle brake lamps. If your brake switch fails in the ON position, you can pull this fuse until you can get a replacement switch. The drain of these lights being on can kill your battery overnight. Do not drive car without brake lights!Answerthe fuse panel is located behind the kick panel on the pass side, just below the dash.(to the right of where your feet sit in the floor board) there is also another power distribution panel under the hood next to the battery. Answerthere is no fuse marked brake lights on jeep cherokee's if you have no brake lights and all bulbs are good your problem is the brake switch mounted on your brake pedal, about 30 bucks.


You have 2004 Jeep Grand Cherokee Laredo brake and abs light is on how can you fix it?

How to change the brake switch on a 2004 Jeep grand Cherokee Laredo


Why do I have no running lights in the rear but my brake lights and turn signals work?

Blown fuse, broken wire, or short in your running lights circuit. you may also not have dash lights. Brake lights, T/S are on a separate circuit. Hope this helps, Mike

Related questions

Which numbered fuse listed in the owners manual actually goes to the brake lights Brake lights are not listed?

should be the tail lights fuse


How do put brake fluid in a Jeep Grand Cherokee?

most likely through the brake fluid reservoir . when in doubt , check your owners manual


Do the headlights and brake lights share a fuse in a 2005 Toyota Camry?

Look in the owners manual. I think they are fused separately.


How do you fill brake fluid?

owners manual


Your 99 f150 has no brake lights all other lights are okrunning lights directials ect?

It has a separate fuse .I bet you have a trailer connection. The correct fuse is noted in the owners manual.


Who can help me my Blinkers and brake lights out on your 2000 ford explorer sport and cant find owners manual need help?

take it to a mechanic I dont wanna "break lights"


What do you if the brake lights on your 96 Cherokee do not come on when pressing the pedal only the center window brake light and you don't have your owners manual and don't know which fuse to change?

I would check the bulbs in the tail lights first. Your Brake switch is working ,because of the third brake light is coming on.Ususally all the brake lights are on the same fuse.... Thanks DomAnswerCenter window light is on a separate circuit. Manufacturers did that so you don't lose all the brake lights at once. Check connections at brake switch and fuses. If ok look for broken wire in harness...............good luck, Mike


Brake lights dont work on your 1997 Ford Taurus..has to be the wires.. maybe the brake switch..?

First things first you need to check your fuses. In the owners manual you will find the location of the fuse that relates to the brake lights. Take the fuse out and hold it up to see if the connection is broken if it is replace and the brake lights should work.


Why would the tail lights work on a 1990 jeep Cherokee but the brake lights don't work?

check the fuse for the brake lights, they have thier own. also check the brake light switch at the at the top of the brake petal


Why do my Jeep Cherokee brake lights stay on?

probably a faulty or mis-aligned brake light switch.


Why don't the brake lights and the tail lights work on your 2001 Jeep Grand Cherokee?

check your fuses


Are there 2 separate fuses for the brake lights and high mount brake light?

It depends on the vehicle. Resubmit question with make, model and year of vehicle. And/Or, consult your owners manual for location and identification of fuses.

People also asked