0
im making my own for a 02 rancher when i get done ill sen you picks and parts list im going to my local hardware store that's all ive seen the man. use is PVC i had a 02 recon ive mad my own on yhat one with the factory air box and a shop vac hose and the facktory installed airt intake it worked great but it burnt up im my house fire
or u can just buy a complete kit, http://www.motoxmall.com/p-S-SSH350-01.html
What else can I help you with?
What are the torque specs for a Honda rancher?
head torque specs for 2002 honda rancher
How do you set timing on 2002 Honda rancher 350 ATV?
how do i check the timing on my 02 honda 350 atv
Where is the radiator on a 2002 Honda rancher 350 4x4?
in front of the cooling fan
Where can you find a 02 Honda rancher 350 wiring diagram?
This is the whole repair manual that includes the wiring diagram, trouble shooting, and more. It is for a 2000- 2003. I have a 2002 Honda rancher 350 also. See link below:
Where is the front skid plate on a 2001 Honda Rancher TRX 350?
I have a 2002 Honda Rancher 350 and the front skid plate attaches to the brush guard near the bottom. A new one is about $34 for a new one at Motosport.com with about $8 shipping. Hope this helps.
What are the torque specs for a Honda rancher?
head torque specs for 2002 honda rancher
Will a 2007 Honda rancher engine fit in a 2002 Honda rancher?
not 100% shure but since 2007 is a 420 and 2002 is 350 and the 350 has a carb and 420 fuel injected but if so i might do it to my 06 rancher
How do you set timing on 2002 Honda rancher 350 ATV?
how do i check the timing on my 02 honda 350 atv
Where do you check the transmission fluid on a 2002 Honda accord?
look for the yellow dipstick in front of the intake snorkel.
Where is the radiator on a 2002 Honda rancher 350 4x4?
in front of the cooling fan
Where can you find a 02 Honda rancher 350 wiring diagram?
This is the whole repair manual that includes the wiring diagram, trouble shooting, and more. It is for a 2000- 2003. I have a 2002 Honda rancher 350 also. See link below:
Where is the front skid plate on a 2001 Honda Rancher TRX 350?
I have a 2002 Honda Rancher 350 and the front skid plate attaches to the brush guard near the bottom. A new one is about $34 for a new one at Motosport.com with about $8 shipping. Hope this helps.
Where is the thermostat on a 2002 Honda Accord?
i would like to know where is the thermostat on a 2002 Honda located
How do you pull the ignition switch on a 2002 Honda rancher?
To pull the ignition switch on a 2002 Honda Rancher, first, ensure the vehicle is in a safe, off position. Remove the plastic cover around the ignition switch by unscrewing the screws holding it in place. Once exposed, gently pull out the ignition switch from its housing, taking care not to damage the wiring. If necessary, disconnect the wiring harness to fully remove the switch.
What can cause a 2000 Honda 350 rancher ATV not to fire?
It is either one of your electric parts gone out such as CDI or the coil but my 2002 honda rancher 350 wouldn't fire and I sprayed WD-40 on the electrical connectors and then it started to fire. If you have been in lots of mud this might have been caused. Make sure the switch is off when unplugging the wires (Honda electrical system is very sensitive).
How do you check oil on a 2002 Honda rancher?
To check the oil on a 2002 Honda Rancher, first ensure the ATV is on level ground and the engine is off. Remove the dipstick from the oil fill cap, wipe it clean, then reinsert it without screwing it in to get an accurate reading. Pull the dipstick out again to check the oil level; it should be between the upper and lower marks. If the oil level is low, add the appropriate type of oil as specified in the owner's manual.
How do you replace petcock valve on a 2002 Honda rancher?
To replace the petcock valve on a 2002 Honda Rancher, first, make sure the fuel tank is empty and disconnect the fuel line from the valve. Remove any mounting screws or bolts securing the petcock to the tank and carefully take it out. Install the new petcock by reversing the removal process, ensuring all connections are secure and leak-free before refilling the tank with fuel. Always check for proper functionality after installation.
