answersLogoWhite

0

If that is a 1.5 sq. mm. cable all laid out in the open and not rolled up it can supply 15 amps, or 3600 watts if the system is 240 volts. Just add up the watts of the bulbs and the total must be less than 3600.

User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Natural Sciences

What size romex for wiring 6 can lights on 15 amp circuit?

For 6 can lights on a 15 amp circuit, you can use 14/2 AWG (American Wire Gauge) NM-B (Romex) cable. This cable consists of three wires: a black (hot) wire, a white (neutral) wire, and a bare copper (ground) wire. Make sure to consult local electrical codes and regulations before proceeding with the installation.


How many flood lights on a 15 amp breaker?

It depends on the wattage of each bulb. Typically you only want to load your circuit to 80% of its rated capacity. Hence a 15 A circuit would be .8 x 15 Amps. Now if you had all 60 Watt bulbs and the supply voltage as 120 V then you could support 24 such bulbs. The key formulas are Voltage = Current x Resistance and Watts = Voltage x Current in your lighting example. However, if the lighting fixtures are rated for a higher value and you just choose to use 60 watts, you should size to the rated capacity of the fixtures on the circuit since someone else may later put in the maximum rated bulb.


How many 120 volt 7 amp draw lights can be run on a 15 kva single phase transformer?

To determine how many 120-volt, 7-amp lights can be run on a 15 kVA transformer, first convert the transformer capacity to watts: 15 kVA equals 15,000 watts. Each light draws 120 volts * 7 amps = 840 watts. Dividing the transformer capacity by the wattage of each light gives 15,000 watts / 840 watts per light ≈ 17.86. Therefore, you can run a maximum of 17 lights on a 15 kVA transformer.


How many lighting outlets are permitted on a branch circuit?

The National Electrical Code typically allows a maximum of 12 lighting outlets on a 15-amp branch circuit and 16 lighting outlets on a 20-amp branch circuit. However, these numbers can vary based on local code requirements, so it's important to check with your local authority having jurisdiction.


Number of 70 watt lights on a 15 amp circuit?

The formula you are looking for is Watts = Amps x Volts.

Related Questions

Outdoor Lighting Installation?

form_title=Outdoor Lighting Installation form_header=10043 Which type of landscape lighting are you in need of?*= [] "In-ground well lights (moonlighting) [] Accent bullets (directionals) [] Down lighting (walls, tree, ceiling mount) [] Bollard lights (garden lights) [] Step or path lights (side lighting) [] Driveway markers [] Underwater well lights [] Uplighting [] Silhouetting [] Want Recommendation" Please approximate the number of landscaping lights you would like installed.*= {Select One,1,2-5,6-15,More than 15,Want Recommendation} What purpose will the landscape lighting serve?*= [] Security [] Accent [] Outdoor sculpture [] Lighting pathway [] Lighting driveway [] Entry lighting


When is a lighting contactor required?

A lighting contactor is a special contactor that is used only for control lighting installations. The contact ratings are incandescent rating and not to be used for motor control. The contactor allows banks of lights to be controlled by one device. The controlling devices could be switches, computers or photocells to bring the lights on at any preset times. <<>> A Contactor used to supply the Power to the lights


Need 15 feet cable how many mm?

15 feet is the same as 4,572 millimeters.


Is 26 receptacles wired on one 15 amp breaker up to code or standard practice for residential 26 receptacles include 10 can lights 4 other lights 12 outlets?

NO! You are drastically in excess of electrical code requirement. A 15 amp circuit should not exceed eight total receptacles and/or lighting devices.


How many pins there is in a SVGA connection?

A cable that converts VGA to RCA has 19 pins. The VGA cable has 15 pins, 3 pins are in the center of the RCA jack, and one pin is unused. This will work to convert an older tv to work with newer cable services.


What size romex for wiring 6 can lights on 15 amp circuit?

For 6 can lights on a 15 amp circuit, you can use 14/2 AWG (American Wire Gauge) NM-B (Romex) cable. This cable consists of three wires: a black (hot) wire, a white (neutral) wire, and a bare copper (ground) wire. Make sure to consult local electrical codes and regulations before proceeding with the installation.


The maximum cable length for a parallel cable is what?

18 inches (45cm)


How many flood lights on a 15 amp breaker?

It depends on the wattage of each bulb. Typically you only want to load your circuit to 80% of its rated capacity. Hence a 15 A circuit would be .8 x 15 Amps. Now if you had all 60 Watt bulbs and the supply voltage as 120 V then you could support 24 such bulbs. The key formulas are Voltage = Current x Resistance and Watts = Voltage x Current in your lighting example. However, if the lighting fixtures are rated for a higher value and you just choose to use 60 watts, you should size to the rated capacity of the fixtures on the circuit since someone else may later put in the maximum rated bulb.


When was Lights Out - film - created?

Lights Out - film - was created on 2011-02-15.


How many lights can you have on a circuit?

15 amps at 80% = 12 amps continuous. Watts = Amps x Volts.


A string of Christmas tree lights has 15 lights One of the lights does not work What is the probability that the defective light is the third one from the plug?

1/15


They custom make this cable to any length you need. I believe mine is 15 feet long. Nice cable for the money.?

They custom make this cable to any length you need. I believe mine is 15 feet long. Nice cable for the money.