0
What else can I help you with?
Does increasing the voltage to an electric heater increase the amperage it draws?
It will increase the current since the water heater is made of a heating element and which is resistive in nature. Ohms law states that V=IR where V is the voltage, I the current and R the resistance. Now the resistance will always remain constant. Thus, when the voltage is increased, the current will also increase.
What is the amperage of a 20kw heater?
To determine the amperage of a 20 kW heater, you can use the formula: Amperage (A) = Power (W) / Voltage (V). For example, at a standard voltage of 240 volts, the amperage would be approximately 83.3 amps (20,000 W / 240 V). If the heater operates at a different voltage, simply adjust the calculation accordingly.
How do I determine the voltage of the wall thermostat for an electric baseboard heater.?
There are two different types of thermostats for electric baseboard heaters. Line voltage and low voltage. Connection to a line stat used the source voltage from the distribution panel and operates like a switch. Because the baseboard heater usually is 240 volts the stat breaks both hot inputs. The stat output goes to the baseboard heater. When the stat calls for heat its internal switch closes and applied the 240 volt to the heater. On the side of the stat will be a voltage and current rating that the stat must operate within. The other type of thermostat is used in low voltage installations. Instead of the switch being in the wall like a line stat, there is a low voltage relay mounted in the baseboard heater itself. This relays coil is usually 24 volts AC. An external 24 volt transformer is needed to supply a voltage to this coil. This 24 volt supply is first taken to the low volt stat and an internal low voltage switch is used to energise the coil of the relay in the baseboard heater. The difference between the two stats is very noticeable in that the line stat is very heavily built with strong termination points. The 24 volt stat is very flimsy in comparison as the current it has to handle is only the relay coils current.
How can one tellwhich wires in the wall are from the power source and which are from the heater when both the wires are the same color?
To determine which wires are from the power source and which are from the heater, you can use a multimeter to test for voltage. Turn off the power to the circuit, then use the multimeter to check for voltage on each wire. The wire with voltage when the circuit is off is from the power source, while the wire with voltage when the heater is on is from the heater. Be sure to proceed with caution and follow all safety guidelines when working with electrical wires.
Can 400volts heater element get supply from 230 volts?
No, a 400 volt heater element cannot be safely operated on a 230 volt supply. To avoid damaging the element and potential safety hazards, it is important to match the voltage rating of the heater element with the supply voltage.
What does high or low voltage do to the capacity of an electric heater?
Yes, voltage effects the output of electric heaters. The wattage output rating of the heater will not be reached due to the lower applied voltage. For example if the heater is 5000 watts at 277 volts, the current is I = W/E 5000/277 = 18 amps. The resistance of the heater is R = W/I (squared) = 5000/18 x 18 (324) = 15.43 ohms. Applying 220 volts on the same heater whose resistance is 15.43 ohms results in this new heater wattage rating. W = E (squared)/R = 220 x 220 (48400)/15.43 = 3137 watts. W = watts, I = amperage, R = resistance in ohms and E = voltage.
What is the recommended voltage for a 4500 watt water heater element?
The recommended voltage for a 4500 watt water heater element is typically 240 volts.
Seat Heater repair on 2004 Buick LeSabre?
To repair a seat heater on a 2004 Buick LeSabre, disconnect the connector and check for voltage. If there is no voltage, replace the switch. If there is voltage, check for an open circuit.
A electric heater works by passing a current of 100 A through a coiled metal wire making it red hot if the resistance of the wire is 1.1 ohms what voltage must be applied to it?
Volts = Amps * ohms 110 = 100*1.1 Thus the voltage was 110 Volts.
How fluorescent bulbs work?
It is a gas filled container and the gas need a higher volts to initially breakdown for conduction so a starter is necessary to increase the line voltage to higher voltage at the same time a heater is applied at both ends to heat the gas to maintain conduction
What is the voltage of a small electric heater if the heater is drawing 12 amperes and has a resistance of 10 ohms?
Voltage is current times resistance, 1.2 x 110 = 132 volts.
What does a heater resistor do?
reduces the voltage available to the blower motor.
What is the minimum temperature setting for a water heater?
The minimum temperature setting for a water heater is typically around 120 degrees Fahrenheit to prevent the growth of harmful bacteria like Legionella.
Does increasing the voltage to an electric heater increase the amperage it draws?
It will increase the current since the water heater is made of a heating element and which is resistive in nature. Ohms law states that V=IR where V is the voltage, I the current and R the resistance. Now the resistance will always remain constant. Thus, when the voltage is increased, the current will also increase.
Can you run a 277volt heater on 220 volts?
Yes, you can but the wattage output rating of the heater will not be reached due to the lower applied voltage. For example if the heater is 5000 watts at 277 volts, the current is I = W/E 5000/277 = 18 amps. The resistance of the heater is R = W/I (squared) = 5000/18 x 18 (324) = 15.43 ohms. Applying 220 volts on the same heater whose resistance is 15.43 ohms results in this new heater wattage rating. W = E (squared)/R = 220 x 220 (48400)/15.43 = 3137 watts. W = watts, I = amperage, R = resistance in ohms and E = voltage.
What is the amperage of a 20kw heater?
To determine the amperage of a 20 kW heater, you can use the formula: Amperage (A) = Power (W) / Voltage (V). For example, at a standard voltage of 240 volts, the amperage would be approximately 83.3 amps (20,000 W / 240 V). If the heater operates at a different voltage, simply adjust the calculation accordingly.
How do you test heater motor peugeot 406?
To test the heater motor in a Peugeot 406, start by checking the fuse associated with the heater system to ensure it's not blown. Next, disconnect the motor's electrical connector and use a multimeter to measure the voltage at the connector while the heater is turned on; there should be a voltage reading if the circuit is functioning correctly. If the voltage is present but the motor does not run, the motor likely needs to be replaced. If there is no voltage, further investigation into the switch or wiring may be necessary.
