0
If you are asking if you can change an 8 Amp Circuit Breaker to 15 Amps, the answer is no. If there is an 8 A breaker in place it is sized to protect the wiring and devices on the circuit. Increasing to 15 A would defeat this protection and could cause a fire or cause a connected device to be destroyed with higher amperage.
What else can I help you with?
Can a circuit breaker be tripped by using 20 amp sockets instead of 15 amp sockets?
A circuit breaker protects the wires that the devices are connected to. If the devices that are connected to the circuit are 20 amps the wire size should be #12 wire fed from a 20 amp breaker. This breaker should not trip unless the circuit is overloaded or a fault occurs on the circuit. If the devices that are connected to the circuit are15 amps the wire size should be #14 wire fed from a15 amp breaker. This breaker should not trip unless the circuit is overloaded or a fault occurs on the circuit. Putting 20 amp sockets on this 15 amp circuit will work but the circuit is limited to the amount of load that can be plugged in. You will not get the full capacity of the 20 socket because the breaker will trip at 15 amps.
What is the continuous current draw on a 20 amp circuit breaker?
Depends on what you have connected to the circuit. It is less than 10 amps or the breaker would trip. A rule of thumb is you design for about 80% load related to the breaker. For 20 amps that would equal 16 amps.
What is type of breaker for 41 amp's?
For a 41 amp load, you would typically use a 50 amp circuit breaker. The general rule is to select a breaker size that is 125% of the continuous load amps or equal to the load amps if it is not a continuous load. In this case, 41 amps is considered a continuous load, so you would round up to the nearest available breaker size, which is 50 amps.
Does a double 50 amp breaker make a 100 amp?
No, a double pole 50 amp breaker protects a 240 volt supply at 50 amps. The number that is on the handle of the breaker is the amperage that the breaker will trip at if an overload occurs on the circuit.
How Many Amps Can a 30 Amp Circuit Handle?
A 30 amp circuit can handle a maximum of 30 amps of current flow continuously without tripping the circuit breaker. It is important not to exceed this amperage to prevent overheating and potential fire hazards.
What is the maximum amperage capacity of a 60 amp circuit breaker?
The maximum amperage capacity of a 60 amp circuit breaker is 60 amps.
What is the maximum amperage capacity of a 90 amp circuit breaker?
The maximum amperage capacity of a 90 amp circuit breaker is 90 amps.
What is the maximum current capacity of a 100 amp circuit breaker?
The maximum current capacity of a 100 amp circuit breaker is 100 amps.
What is the maximum current capacity of an 80 amp circuit breaker?
The maximum current capacity of an 80 amp circuit breaker is 80 amps.
What is the maximum current rating for the 30 amp circuit breaker?
The maximum current rating for a 30 amp circuit breaker is 30 amps.
What is the maximum amperage capacity of a 150 amp circuit breaker?
The maximum amperage capacity of a 150 amp circuit breaker is 150 amps.
What is the maximum amperage capacity of the circuit breaker 30 amp?
The maximum amperage capacity of a 30 amp circuit breaker is 30 amps.
What is the maximum current rating for a 15 amp circuit breaker?
The maximum current rating for a 15 amp circuit breaker is 15 amps.
What is the maximum current capacity of the circuit breaker rated at 150 amp?
The maximum current capacity of a circuit breaker rated at 150 amps is 150 amps.
What is the maximum current capacity of a 30 amp breaker for a 240v circuit?
The maximum current capacity of a 30 amp breaker for a 240v circuit is 30 amps.
What is the recommended amperage for a 30 amp RV circuit breaker panel?
The recommended amperage for a 30 amp RV circuit breaker panel is 30 amps.
What is the maximum amperage rating for a circuit breaker that can safely protect a 20 amp circuit?
The maximum amperage rating for a circuit breaker that can safely protect a 20 amp circuit is 20 amps.
